Jenn-Air W10676382C Manuale Utente
5
COOKTOP USE
Cooktop Controls
Electric igniters automatically light the surface burners when
control knobs are turned to HI and will automatically reignite if the
flame is extinguished.
control knobs are turned to HI and will automatically reignite if the
flame is extinguished.
If a cross draft is present, the flame may be affected and some
sparking may occur. This is normal.
sparking may occur. This is normal.
Before setting a control knob, place filled cookware on the grate.
Do not operate a burner using empty cookware or without
cookware on the grate.
Do not operate a burner using empty cookware or without
cookware on the grate.
To Set:
1. Push in and turn knob counterclockwise to HI.
2. Turn knob to anywhere between HI and LO. Use the following
chart as a guide when setting heat levels.
*For a more delicate simmer, see the “Melt Cap” section.
Power failure
In case of power failure, the surface burners can be lit manually.
Hold a lit match near a burner and turn knob counterclockwise to
HI. After burner lights, turn knob to setting.
Hold a lit match near a burner and turn knob counterclockwise to
HI. After burner lights, turn knob to setting.
IMPORTANT: Burner reignition feature does not work without
power.
power.
Sealed Surface Burners
Burner installation:
To install the burner base, insert the igniter electrode into the
burner base hole or notch.
IMPORTANT: Do not obstruct the flow of combustion and
ventilation air around the burner grate edges.
burner base hole or notch.
IMPORTANT: Do not obstruct the flow of combustion and
ventilation air around the burner grate edges.
Burner cap: Always keep the burner cap in place when using a
surface burner. A clean burner cap will help avoid poor ignition
and uneven flames. Always clean the burner cap after a spillover
and routinely remove and clean the caps according to the
“General Cleaning” section.
surface burner. A clean burner cap will help avoid poor ignition
and uneven flames. Always clean the burner cap after a spillover
and routinely remove and clean the caps according to the
“General Cleaning” section.
Gas tube opening: Gas must flow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil
and do not allow spills, food, cleaning agents or any other
material to enter the gas tube opening. Keep spillovers out of gas
tube by always using a burner cap.
opening for the burner to light properly. Keep this area free of soil
and do not allow spills, food, cleaning agents or any other
material to enter the gas tube opening. Keep spillovers out of gas
tube by always using a burner cap.
SETTING
RECOMMENDED USE
HI
■
Start food cooking.
■
Bring liquid to a boil.
■
Hold a rapid boil.
■
Quickly brown or sear food.
■
Fry chicken.
Medium
Between HI and LO
Between HI and LO
■
Maintain a slow boil.
■
Fry or sauté foods.
■
Cook soups, sauces and gravies.
■
Stew or steam food.
LO
■
Simmer.*
■
Keep food warm.
Simmer
■
Simmer sauces.
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
or fire.
Standard Burner
A. Cap
B. Spreader
B. Spreader
C. Electrode
Dual Flame Burner
A. Cap
B. Spreader
B. Spreader
C. Electrode
REMEMBER: When cooktop is in use, the entire cooktop
area may become hot.
area may become hot.
A
B
C
A
B
C