EdgeStar 866-319-5473 Dépliant

Installation Guide

Beer Dispenser

866-319-5473

For assistance, please call:

Now mount the 

CO

2

 cylinder 

holder(9) to the cabinet. Match 

up the holes on the holder with 

the four screws jutting out of the 

back of the cabinet and slide the 

holder down to lock it in place. 

Position the 

CO

2

regulator(6) in 

the holder so that you will be 

able to read the numbers on the 

gauge and have easy access to 

the shut-off valve.

Place the metal keg floor support(11) back into the cabinet. 

Carefully tilt beer keg(17) and rest the edge on the keg floor 

support on the bottom of the interior cabinet. Slide the keg in 

slowly, ensuring that it is properly located, and all hoses are 

clear of obstructions. Close door and enjoy.

Screw the black faucet handle(1) onto 

the faucet (2). Line up the metal “teeth” 

on the faucet with the metal “teeth” of 

the faucet adapter on the front of the 

tower(3). Make sure the faucet is 

vertical with the black handle facing the 

ceiling. The faucet should then be first 

“hand tightened,” then secured with the 

faucet wrench(18). Now place the plastic 

drip tray(5) beneath the faucet. 

To connect the keg coupler(10) to the keg(17), first make sure 

the black pull handle of the keg coupler is in the closed 

(diagonal/upper) position. Insert the keg coupler into the 

locking neck of the beer keg and turn clockwise 25° to lock in 

into place. Now the keg coupler is secured to the keg. 

Now connect the beer line from the 

tower(3) to the keg coupler. Insert the 

neoprene washer(14) (provided with 

the kit) into the beer line hex nut (the 

beer line is the line coming 

from/going to the tower and faucet).

Remove the blue rubber protective 

cap located on top of the keg coupler 

and screw the nut with the neoprene 

washer to the top of the keg coupler; 

hand-tighten firmly.

Make sure the 

CO

2

 regulator(6) shut off valve is 

closed- the switch below the main body should be 

perpendicular to the tubing. Install the 4 ft. 

CO

2

gas line tube(7) to the regulator by attaching one 

end of the tube into the hose barb connection on 

the

CO

2

 regulator. Secure the tube by using one of 

the two self-locking red plastic snap-on 

clamps(15). Use pliers or clamp crimpers to snap 

the clamp on as high as possible. Make sure the 

clamp does not impeed the valve. Then remove the 

black rubber plug from the back of the unit and 

feed the remaining unused end of the tubing 

through the hole. 

Make sure the 

CO

2

 cylinder(8) is full and 

closed. Then attach the 

CO

2

 regulator(6) 

to the 

CO

2

 cylinder by screwing the loose 

golden regulator nut into the cylinder valve 

and tightening with a wrench or pliers. 

Note that a fiber washer is normally 

required to connect a regulator to a 

CO

2

cylinder, but the standard regulator 

provided includes a built-in o-ring.

To secure the tank connection, 

pull the tap handle out (away 

from the keg coupler(10)) and 

push down until it locks into 

position. Listen for the “click” 

of the pull handle when it 

shifts into the final downward 

position. The keg is now 

tapped.

Now attach the remaining open end of the 

CO

2

gas line tube(7) to 

the keg coupler’s hose barb(10). Then secure the tube by using 

the remaining self-locking red plastic snap-on clamp(15). Use 

pliers or clamp crimpers to snap the clamp securely as close to the

coupler as possible.

(A) With the shut-off valve on the regulator(6) closed, open the valve on the gas cylinder(8) completely. (B) With your 

fingers or a pair of pliers, loosen adjustment nut allowing adjustment screw to be turned counter-clockwise until 

adjustment screw can no longer turn. (C) Now slowly turn the regulator adjustment screw clockwise until the desired 

pressure is shown on the output pressure gauge. Under normal circumstances, we recommend setting the regulator at 

12psi. NOTE: Other conditions, such as altitude or special beer type, may require some adjustment. On regulators 

designed for draft beer, turning clockwise will increase the output pressure, and turning counter-clockwise will decrease 

the output pressure. (D) Open the shut-off valve on the regulator-the switch below the main body should be parallel to 

the tubing. Gas should now flow from the regulator to the keg coupler(10). You will hear the keg pressurizing. The 

output needle will drop momentarily while the pressure is equalizing. Then, the needle will return to the point you set it 

at. (E) The keg coupler is designed with a pressure relief valve (PRV). Pull the ring on the PRV briefly to allow gas to 

vent. This will permit gas to flow through the regulator and help obtain a more accurate reading on the output pressure 

gauge. (F) Re-check the output pressure on the regulator, and if necessary re-adjust using step B until the desired 

pressure is shown.

NOTE: It is always wise to follow up any adjustment to the regulator with a brief pull of the PRV ring to ensure an 

accurate output reading. 

Warning: 

CO2 can be dangerous! CO2 cylinders contain high-pressure gas, which can be hazardous if 

handled improperly. Please handle with care.

Note: Included accessories may not be as pictured

Warning:

 This guide is provided for informational purposes only. If you have any questions about 

the installation of this appliance, feel free to contact EdgeStar service at 866.319.5473 or consult 

a qualified installer. Neither the manufacturer nor its distributors shall be liable for any incidental, 

consequential, indirect, special, or punitive damages of any nature, including without limitation, 

lost revenues or profits, or any other damage whether based in contract, tort, or otherwise. 

B

A

C

D

E

F