Lexmark 5200 Guida All'Installazione Rapida

E.C. 21D005 

© 2004 Lexmark International, Inc. All rights reserved. 

Connect the USB cable.

Make sure your 
computer is on. 

Insert the CD. Follow the 
instructions on your computer 
screen.

• Refer to your User’s Guide.
• Visit our Web site: 

• Call us at 1-800-332-4120. 

Monday-Friday (9:00 AM - 9:00 PM EST)
Saturday (Noon-6:00 PM EST)

Note: Phone number and support times may change without notice.

Record the following information (located on your store receipt and the 
back of your printer) and have it ready when you contact us so that we may 
serve you faster:

Machine Type number 

Serial number 

Date purchased 

Store where purchased 

Press to 

print 

an alignment page.

You may discard the 
alignment page after it 
prints.

If you are using 
your All-In-One 
with a 
computer, 
continue to 
step 12.

If you are using 
your All-In-One 
without a 
computer, you 
are finished.

The Power light is 
not lit

Is the power cord pushed all 
the way into the All-In-One?

Disconnect the power cord from 
the wall outlet, and then from 
the All-In-One. Reconnect the 
power cord by pushing it all the 
way into the connector on the 
All-In-One, and then into the 
wall outlet.

Is the All-In-One connected to 
a working electrical outlet?

Connect the All-In-One to an 
electrical outlet that other 
electrical devices have been 
using.

Software will not 
install

Is your operating system 
compatible with the All-In-
One?

The All-In-One supports these 
operating systems:

• Windows 98
• Windows Me
• Windows 2000
• Windows XP
• Mac OS X version 10.1.5
• Mac OS X version 10.2.3 and 

later

Alignment page or 
test page will not 
print

Is the All-In-One on?

Press the Power button. If the 
Power light does not come on, 
see the “The Power light is not 
lit” symptom at the beginning of 
this table.

Do you see an error 
message?

See “Error messages 
troubleshooting” in your User’s 
Guide.

Is your All-In-One connected 
to your computer through 
another device, such as a 
USB hub or switch box?

Disconnect the USB cable from 
any other devices and directly 
connect it between the All-In-
One and your computer. For 
help, see step 13.

Did you remove the sticker 
and tape from the bottom of 
each print cartridge? 

Are the print cartridges 
installed properly?

Remove the print cartridges, 
check for the sticker and tape 
and then reinsert them. For 
help, see step 8 and step 9.

Is the paper loaded correctly?

See step 6.

The control panel 
displays text in the 
wrong language

Did you select a language?

1 Press the Power button to 

turn on the All-In-One.

2 Press and hold both the 

Power and Cancel buttons 
for 10 seconds. Language 
text appears on the display.

3 Press the + button repeatedly 

until the language you want 
appears on the display.

4 Press the Arrow button to 

select that language.

The following cartridges work with your printer.

• 31

• 32
• 34

• 33
• 35

1 Click Cancel on any New Hardware screens.
2 Eject and reinsert the All-In-One software CD.

If the All-In-One software install screen does not appear:

a From your desktop, double-click My Computer (In Windows XP, click 

à

 My Computer).

b Double-click the CD-ROM drive icon. If necessary, double-click setup.exe.

c When the All-In-One software installation screen appears, click Install.

d Follow the instructions on the screen.

1 From your desktop, double-click the Lexmark 5200 Series Installer icon.
2 Double-click Install and follow the instructions on the screen.

 

Note: New Hardware screens appear only for Windows users. For 

Macintosh, continue to step 15.

Windows 98/Me

Windows 2000/XP

Click Cancel

on all New Hardware screens.