Lexmark C770 Istruzione Sull'Installazione
15
IPDS Printer and Host Setup Guide AS/400 and iSeries Twinax Printing Using the Adapter for SCS
2.
AS/400 and iSeries Twinax Printing Using the
Adapter for SCS
With the optional Card for IPDS/SCS/TNe and the optional Coax/Twinax Adapter for SCS installed, the printer
can receive, process, and print AFP/IPDS print jobs over TCP/IP from the following IBM software:
can receive, process, and print AFP/IPDS print jobs over TCP/IP from the following IBM software:
•
PSF/400 V3R1-R3, V3R6-R7, V4R1-R5, V5R1-R4, or greater
Some printers do not support the Coax/Twinax Adapter for SCS. Refer to
to determine if your printer supports the adapter. Note that no MFPs support Twinax printing.
The information below will lead you through the steps for setting up the AS/400, or iSeries, and the printer to
print IPDS jobs over a direct Twinax connection using the optional Coax/Twinax Adapter for SCS. Refer to the
IPDS User’s Guide for detailed instructions on using the control panel to select and change option settings.
print IPDS jobs over a direct Twinax connection using the optional Coax/Twinax Adapter for SCS. Refer to the
IPDS User’s Guide for detailed instructions on using the control panel to select and change option settings.
Steps
The following steps must be completed to begin printing IPDS jobs.
1
2
3
4
5
6
Step 1
Configure the Adapter IPDS and SCS Twinax Addresses
When the printer has both the "Card for IPDS and SCS/TNe" and the "Coax/Twinax Adapter for SCS" installed,
it is possible to print IPDS jobs using the IPDS emulation in the Card for IPDS and SCS/TNe and SCS jobs
using the SCS emulation of the Adapter for SCS.
it is possible to print IPDS jobs using the IPDS emulation in the Card for IPDS and SCS/TNe and SCS jobs
using the SCS emulation of the Adapter for SCS.
To use both emulations, when you install and configure the option cards, assign a twinax address for the IPDS
device address and a different twinax address for the SCS device address in the Adapter for SCS. This is done
using the SCS DEV.ADDR. and IPDS DEV. ADDR. options as shown below. In our examples, we will give
address 0 to SCS and address 2 to IPDS.
device address and a different twinax address for the SCS device address in the Adapter for SCS. This is done
using the SCS DEV.ADDR. and IPDS DEV. ADDR. options as shown below. In our examples, we will give
address 0 to SCS and address 2 to IPDS.
Important:
If the IPDS device address and the adapter SCS device address are the same, the Adapter SCS
device address will be used and the IPDS device address will be ignored. The word DUPLICATE will
display in the control panel.
device address will be used and the IPDS device address will be ignored. The word DUPLICATE will
display in the control panel.
Be certain to set the correct twinax addresses in the Adapter for SCS for both the SCS device address
and the IPDS device address before physically connecting your printer to the twinax wiring system. If
you were to incorrectly enter the same address used by another device, you would disable that device.
If you do not know your printer's correct address, contact your network administrator.
and the IPDS device address before physically connecting your printer to the twinax wiring system. If
you were to incorrectly enter the same address used by another device, you would disable that device.
If you do not know your printer's correct address, contact your network administrator.
Step 1A: Configure the Printer Adapter IPDS Device Address - or Disable IPDS Printing
The following options for the Adapter for SCS only appear when the IPDS emulation is detected in the printer.
The IPDS Device Address is used to select the twinax address for the IPDS emulation or to disable the IPDS
emulation.
emulation.