3M random orbital sanding for cabinet shops Manuale Utente

3M

™

Stikit

™

Disc 415U - 125 discs/roll (80 through 120), 

250 discs/roll (150 through 220)
3M

™

Stikit

™

Disc 415U - 5" (5 hole) discs/roll 

(80 through 120), 250 discs/roll (150 through 220)
3M

™

Hookit

™

II Disc 415U - 50 discs/box

3M

™

Stikit

™

Disc 734U - 75 discs/roll

3M

™

Hookit

™

Disc 734U - 50 discs/box

3M

™

Hookit

™

II Disc 734U - 50 discs/box

Accessories
There are three types of disc pads available:

Standard: tapered edge offers conformability along the edge of the disc

Low Profile: consistent support across the entire disc

Low Profile Finishing: soft disc pad for sanding applications requiring
more conformability

734U

Grades

Stikit 5''

UPC # 051131-

Hookit 5''

UPC # 051131-

Hookit II 5''

UPC # 051131-

P80

00309-5

01767-2

00667-6

P100

00308-8

01766-5

00666-9

P120

00307-1

01765-8

00665-2

P150

00306-4

01764-1

00664-5

P180

00305-7 

01763-4

00663-8

1. Always use protective glasses as recommended

in ANSI Standard Z87.1.

2. Use appropriate body protection such as 

gloves, safety shoes, and aprons where 
appropriate.

3. Do not exceed the maximum operating speeds 

stated on the product labels.

4. Use guards and dust collection system, if 

provided, with equipment.

5. Periodically check machinery and mountings 

hardware to make sure they are in good 
operating condition. Repair or replace 
damaged machinery and mounting hardware.

6. Inspect product prior to installation on 

equipment for defects or damage.

7. During use, if unusual vibrations or changes 

occur, immediately stop the equipment. 
Determine the cause and correct.

1. Sand the entire work piece to give a consistent 

finish.

2. Have the work area well lit.
3. Check that the random orbital sander backup 

pad has a clean, even surface to reduce any 
chances of wild defects.

4. Clean all work surfaces prior to sanding.
5. To avoid “swirls” or “hook” marks when 

using a pneumatic (air) sander, ensure that the 
sander has the proper air pressure. When the 
tool is running, it should have a minimum of
90 PSI (pounds per square inch).

6. Whether using an electric or air sander, start 

the sander flat on the work piece and keep the 
backup pad as flat as possible to prevent 
gouging.

7. NEVER stop the sander while the tool is in 

contact with the work piece. Stopping the 
sander on the work piece may create wild 
scratches. Stop the tool as it is removed from 
the work piece.

8. Sand in a smooth, back and forth, up and down

motion.

9. Clean wood dust from the work piece between 

sanding steps. This will assist in reducing
“the re-sanding of dust”.

Market:  Woodworking 
Application Description:  Random Orbital Sanding for Cabinet Shops

3M

™

Stikit

™

Disc 255L - 100 discs/roll

3M

™

Hookit

™

Disc 255L - 75 discs/box (P80), 

100 discs/box (P100 through P220)
3M

™

Hookit

™

5" (5 hole) Disc 255L - 75 discs/box (P80),

100 discs/box (P100 through P220)

255L

Grades

Stikit 5''

UPC # 051144-

Hookit 5''

UPC #  051131-

Hookit

5'' (5 holes)

UPC #  051131-

P80

82471-7

00967-7

01067-3

P100

82470-7

09966-0

01066-6

P120

82469-4

00965-3

01065-9

P150

82468-7

00964-6

01064-2

P180

82467-0

00963-9

01063-5

P220

82466-3

00962-2

01062-8

415U

Grades

Stikit 5''

UPC # 051144-

Stikit

5'' (5 holes)

UPC # 051144-

Hookit II 5''

UPC # 051111-

80

77223-0

77224-7

49675-6

100

77227-8

77228-5

49645-9

120

77230-8

77231-5

49646-6

150

77234-6

77235-3

49647-3

180

77237-7

77238-4

49648-0

220

77241-4

77242-1

49649-7