Sony GC79 Manuale Utente
76
Appendix B - Windows Log on using a GSM/GPRS Dial-up Connection
Appendix B - Windows Log on using a GSM/GPRS
Dial-up Connection
The GC79 PC Card supports the Windows Log on using dial-up connection feature.
To log on to Windows using a GSM or GPRS dial-up connection the GC79 PC Card must be inserted
and the radio enabled before you log on. To enable the radio prior to logon, select Enable radio
immediately when card inserted checkbox on the Radio Power preferences tab, see Radio Power
Tab on page 17 for more details.
and the radio enabled before you log on. To enable the radio prior to logon, select Enable radio
immediately when card inserted checkbox on the Radio Power preferences tab, see Radio Power
Tab on page 17 for more details.
Important!
Never start your PC in this mode if you are in a location where mobile devices shouldn’t
be used, for example, on an aeroplane, in hospital or near a blast site.
be used, for example, on an aeroplane, in hospital or near a blast site.
Only check this option if you need to log on to a Windows Domain via a wireless dial-up connection.
This will permit the GC79 to register with the GSM network and establish a connection when the
Windows logon screen is displayed.
This will permit the GC79 to register with the GSM network and establish a connection when the
Windows logon screen is displayed.
Note:
It is not possible to display network status or signal strength during the Windows logon
procedure, so you should allow enough time for the GC79 to find and register with the network
prior to attempting to log on.
procedure, so you should allow enough time for the GC79 to find and register with the network
prior to attempting to log on.
The dial-up connections available to the Windows Logon must have been created by a user account
with Administrator privilege and designated For all users. This must be done using the Windows
Network Connection Wizard, because the GC79 Manager can only create connections for the
current user ID. Normally the Windows Logon using dial-up connection will be using a CSD/
HSCSD session to a corporate network, so that the logon credentials can be validated by a
Windows Domain Server.
with Administrator privilege and designated For all users. This must be done using the Windows
Network Connection Wizard, because the GC79 Manager can only create connections for the
current user ID. Normally the Windows Logon using dial-up connection will be using a CSD/
HSCSD session to a corporate network, so that the logon credentials can be validated by a
Windows Domain Server.
Note:
A HSCSD networking session will require some additional settings to be added to your ini
string, see Appendix D- Initiating a HSCSD Connection from Outside the GC79 Manager on
page 79.
string, see Appendix D- Initiating a HSCSD Connection from Outside the GC79 Manager on
page 79.
There may be special circumstances where a GPRS dial-up connection is required for logon.
To create a GPRS dial-up connection, follow these steps:
To create a GPRS dial-up connection, follow these steps:
1. Create the Windows dial-up connection using the Windows Network Connection Wizard.
For the telephone number, use *99***3#.
2. Set the GPRS context parameters in the GC79 PC Card.
Open a Windows Hyperterminal session on the same port as the GC79, running at 115Kbps,
and type in the following AT Command.
and type in the following AT Command.
AT+CGDCONT=3,“IP”,“<AccessPointName>”,“”,0,0
where <AccessPointName> is the name of the special GPRS access point for your corporate
GPRS service.
where <AccessPointName> is the name of the special GPRS access point for your corporate
GPRS service.
Note:
In this example, we used GPRS Context 3. There are 1-10 possible contexts supported by the
GC79 PC Card (1..8). Context ID 2 is reserved for connections created by the GC79 Manager.
GC79 PC Card (1..8). Context ID 2 is reserved for connections created by the GC79 Manager.
Refer to the GC79 AT Commands Manual or contact your service provider for further assistance.