Nortek Security & Control LLC/GTO Access SGET Manuale Utente
The SGET is part of Linear PRO Access control product line. In a typical
installation, the SGET is mounted on a motorized gate, door or barrier arm and
wired to a 10K exterior safety edge sensor which presents a closed circuit across
the connecting wires when an object is hit during the closing of a gate. To insure
full compatibility with all gate edge supervision features, Linear recommends Miller
gate edge sensors with 10K only. Please specify when ordering sensor. If the edge
sensor is pressed for 1/4 second, the SGET transmits a message to the SGER to
reverse the movement of the gate.
installation, the SGET is mounted on a motorized gate, door or barrier arm and
wired to a 10K exterior safety edge sensor which presents a closed circuit across
the connecting wires when an object is hit during the closing of a gate. To insure
full compatibility with all gate edge supervision features, Linear recommends Miller
gate edge sensors with 10K only. Please specify when ordering sensor. If the edge
sensor is pressed for 1/4 second, the SGET transmits a message to the SGER to
reverse the movement of the gate.
The SGET circuit board has been coated to prevent moisture damage and is
mounted inside a weather resistant fiberglass box. The mounting box attaches to
the gate through sealed interior mounting screws.
mounted inside a weather resistant fiberglass box. The mounting box attaches to
the gate through sealed interior mounting screws.
TYPICAL INSTALLATION
Loosen the four screws on transmitter top and remove cover. Install 2 “C” size
batteries at this time.
batteries at this time.
Refer to diagram below for transmitter parts location and details.
Mount safety edge according to manufacturer’s instructions included with the
product.
product.
Choose a location as high as possible on gate in a secure position. Use the
template attached to mark the location for the transmitter. You may have to
attach a metal or wood plate to mount transmitter. Use a 3/32” bit and drill
holes. Attach SGET to gate using the four #6 self-tapping drill point screws.
template attached to mark the location for the transmitter. You may have to
attach a metal or wood plate to mount transmitter. Use a 3/32” bit and drill
holes. Attach SGET to gate using the four #6 self-tapping drill point screws.
Unscrew the cable grip about 3/4 of the way and thread the safety edge cable
through the cable entry on the transmitter.
through the cable entry on the transmitter.
Attach safety edge cable to terminals as shown. Tighten cable grip assembly
using pliers to assure a water tight seal.
using pliers to assure a water tight seal.
SGET
DIGITAL GATE
Transmitter
Transmitter
Installation Instructions
PRO ACCESS
TM
Linear PRO Access • 3121 Hartsfield Road • Tallahassee, FL 32303
1.800.543.4283 • linearproaccess.com
Description
STEP 2 Remove Cover and Install Batteries
STEP 4 Mount SGET
STEP 5 Assemble Cable Grip
STEP 6 Attach Cable
STEP 1 Locate Parts
STEP 3 Mount Safety Edge
REMOVE
COVER
COVER
INSTALL
“C” BATTERIES
“C” BATTERIES
SGET
TRANSMITTER
SAFETY EDGE
SENSOR
GATE
OPERATOR
CABLE GRIP
ASSEMBLY
TO SAFETY
EDGE
TO SAFETY
EDGE
ATTACH EDGE
SENSOR CABLE
TO TERMINALS
1.77”
3.88”
WELD PLATE
TO GATE
ATTACH SGET
TO GATE
INSTALL
SAFETY EDGE
“C” Size
Battery Holders
Programming Button
Antenna
Wire
Terminals
PRINTERS INSTRUCTIONS
INSTR,INSTL,SGER SERIES - GTO P/N:
INSTR,INSTL,SGER SERIES - GTO P/N:
10016915
- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - SIDE 1 of 2