TE Connectivity Black 58079-3 Scheda Tecnica

Codici prodotto

58079-3

Instruction Sheet

Crimping Die Assemblies

408--9278

LOC B

of 4

2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

TOOLING ASSISTANCE CENTER 1--800--722--1111

PRODUCT INFORMATION 1--800--522--6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

25 APR 11 Rev B

58079- 3 and 58080- 3

PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume

applications. A wide selection of powered application equipment for extended--use, production operations is available.

Figure 1

Die Retention

Screw

Upper Die

(Crimper)

Color

Dot

Code

Lower Die

(Anvil)

Wire Size Range

Markings

Crimping

Chamber

Wire Size

Range

Markings

1. INTRODUCTION

This instruction sheet covers application and

maintenance procedures for Crimping Die Assemblies

58079--3 and 58080--3. See Figure 1. Each die

assembly is used with Hand Crimping Tool Frame

58078--3, which will crimp the Ultra--Fast Plus Fully

Insulated FASTON* Terminals listed in Figure 2.

Refer to Instruction Sheet 408--6976 (supplied with

tool frame) for specific tooling information. Product

part number information is available in Catalog 82004.

Dimensions are in millimeters [with inch

equivalents in brackets]. Figures are for

identification only and are not drawn to scale.

Reasons for reissue are provided in Section 7,

REVISION SUMMARY.

2. DESCRIPTION

Each die assembly consists of an upper die (crimper)

and a lower die (anvil), a die retention screw (on

upper die), and a hex wrench for securing the socket

head setscrew to the lower die and onto the hand tool

platform. When mated, the dies form two crimping

chambers, each marked with the wire size range.
The die assemblies are identified by the part number,

color dot code, and applicable wire range markings.

Refer to Figure 2. The color dot code on the die

assembly must match the color--coded terminal.

3. DIE ASSEMBLY INSTALLATION

3.1. Installing Lower Die

1. Close tool frame handles until ratchet releases,

then allow handles to open FULLY.
2. Slide lower die onto lower jaw platform of tool

frame. Make sure that the hole on the side of the

lower die aligns with the socket head setscrew on

the platform. See Figure 3.

If lower die will not position properly, use hex

wrench provided with die assembly to turn

socket head setscrew either in or out until lower

die positions properly.

3. Using hex wrench, turn socket head setscrew

CLOCKWISE until snug. Do NOT overtighten.

3.2. Installing Upper Die

1. Remove die retention screw from upper die.
2. Slide upper die onto upper jaw platform of tool

frame. Make sure the color dot code on upper die

is on the same side as the color dot code on lower

die. See Figure 3.

WIRE

ULTRA--FAST PLUS

TERMINALS

DIE ASSEMBLY

SIZE

(AWG)

INSUL

DIA.

(MAX)

SERIES PART NO.

COLOR

CODE

DOT

PART NO.

3 43

187

2--520409--2

22--18

3.43

[.135]

.187

2--520411--2

Red

58079--3

[.135]

.250

2--520407--2

4 06

187

3--520410--2

16--14

4.06

[.160]

.187

3--520412--2

Blue

58080--3

[.160]

.250

3--520408--2

Figure 2

ORI

INAL

STRUCTI

NOTE