Jensen VM9022 Manuale Utente

14

VM9022

Press the  /SRC button (6) (or any other button on the front 

of the unit except reset), or the  /POWER button (4) on the 
remote control, to turn the unit on. The buttons on the front of 
the unit light up and the current mode status appears on the 
TFT screen (17). 

Press and hold the   button to power off the unit.The monitor 
is drawn back into the main compartment.

An audible beep tone confirms each function selection. The 
Beep tone can be disabled through the Setup menu. 

To increase or decrease the volume level, turn the rotary 
encoder (5) on the front panel or press the VOL+/ VOL- 
buttons (15, 16) on the remote control. When the volume 
level reaches “0” or “40”, a beep sounds, indicating that the 
adjustment limit has been reached. The volume ranges from 
“0” to “40”. The TFT screen displays the volume level for 3 
seconds.

This feature allows the user to select a turn-on volume setting 
regardless of the volume setting prior to turning the unit off. 
To program a specific turn-on volume level, turn the AUDIO 
control (2) to adjust the volume to the desired turn-on volume. 
Push and hold the AUDIO button while the yellow speaker 
icon and level indication is displayed on the screen. The unit 
will beep two times to confirm your turn-on volume setting. 

Press the MUTE button on the front panel (8) or remote 
control (3) to mute the volume from the unit. Press the MUTE 
button again to restore the volume. “MUTE” is displayed on 
the screen. Adjusting the volume or using any of the audio 
setup features cancels the mute function.

If the “MUTE” wire is connected, audio output mutes when a 
telephone call is received by a cell phone.

Press the SRC button on the front panel (6) or remote control 
(8) to change between available playing sources in the 
following order: RADIO, SAT, DISC, NAV, BT, iPod, SD, USB, 
AUX1,

 

AUX2 and CAMERA. The playing mode is displayed 

on the TFT screen.

External peripheral devices can be connected to this unit via 

RCA output (AUX IN 2) or the MediaLink

4

. 

Select “AUX1” to play an auxiliary device connected via the 
MediaLink RCA or 3.5mm inputs. For example, you can play 
music files from a portable music player, video from a video 
camera and even view photos stored on a digital camera.

Select “AUX2” mode to access and control auxiliary devices 
connected to the “AUX IN 2” inputs on the back of the radio.

While navigating, other sources may be selected and listened 
to such as AM-FM Tuner, CD, etc. To select a source, press 

the /SRC button (6) and then select a source from the Front 
Source Menu. Navigation voice prompts will be heard 
automatically, although the navigation map cannot be seen. 
(The selected source audio will be muted until the navigation 
voice prompt command is completed, after which the source 
audio will resume.)

To access the SOURCE MENU, touch the TFT screen in the 
top left corner of the screen. 

This menu allows you to select a source for the front or rear 
zone. Touch FRONT or REAR to choose the zone for which 
you would like to specify the source. (See “Multi-ZONE 
Operation” on page 16.)

The Audio Control menu features a 7-band graphic equalizer, 
which allows you to easily adjust your audio system to meet 
the acoustical characteristics of your vehicle, which vary 
depending on the type of vehicle and its measurements. 
Proper setting of the Fader and Balance boosts the effects of 
the cabin equalizer.

Press the AUDIO button (5) on the front panel to display the 
audio menu. 

VIDEO

LEFT

RIGHT

3.5mm - Audio

iPod Connector
(GEN 5 Recommended)

USB Connector (Type A)

RCA Inputs (AUX 1)

3.5mm Left & Right
Stereo Inputs (AUX 1)

DISC

RADIO

SD

iPod

SAT

USB

AUX 1

AUX 2

F

R

O

N

T

R

E

A

R

NAV

CAMERA

BT

+12 —

0 —

–12 —

80

250

600

1k

4k

10k

16k