Home Automation OmniPro II Manuale Utente

 
The OmniPro II can be set up to speak descriptive names such as "FRONT DOOR" for control zones, units, buttons, codes, 
temperatures, areas, and messages. These names will be spoken over the telephone along with the item number that is normally 
spoken.  Voice descriptions for messages can be spoken over a speaker when used with a Two-Way Audio Module.   
 
To enter the Set Up Voice menu, from the Setup menu, press the 8 (VOICE) key. 
 
 

 

 

SET UP VOICE

 

 

 

 

1=CTRL  2=ZONE  3=BTTN 

↓

 

 

 

 

 

 

4=CODE  5=TEMP  6=AREA

 

 

 

 

8=MSG                  

↑

 

 
Select the item that you would like to give a voice description.  Use the arrow keys to scroll through the list of names.   
 
To enter a voice description, enter the code shown next to the voice description in Appendix C for each description (word or 
group of words), then press the ' # ' key.  After you have entered the complete description for each item (unit, zone, button, code, 
temperature, area, and message), press the ' # ' key twice.  You may enter up to six (6) descriptions (word or group of words) for 
each unit, zone, button, code, temperature, area, and message.   
 
   UNIT 

1 

VOICE:

 

 

 

 

                       

↓

 

 
   UNIT 

1 

VOICE:

 

 

 

 

144 109                

↓

 

 
When Unit 1 is spoken over the phone, the OmniPro II will say, "UNIT 1 - PORCH LIGHT". 
 
 

 
The final setup item is accomplished over the telephone.  This is the address that the system says when it dials out in an 
emergency.  Your voice will be recorded on computer chips in the OmniPro II controller and saved to be played back in the 
emergency message when the system dials out for an alarm. 
 
Pick up an inside phone and press the ' # ' key on the telephone within 5 seconds of picking up the phone.  The OmniPro II will 
respond with a menu.  Press 8 on the telephone keypad, then 8.  The unit will say "ADDRESS IS:" then the OmniPro II will play 
back the message stored in the Address memory if one has been entered by your installer.  
 
To record your address, Press 9, then enter the Master Code.  The OmniPro II will say "RECORD ADDRESS", then BEEP.  In a 
normal tone of voice, say your name and address and any helpful information for locating your house.  
 
"THE JONES RESIDENCE, 1234 JOHNSON STREET, CORNER OF JOHNSON AND THIRD STREET" 
 
The unit will beep after 8 seconds, then play the address back to you.  If you are not happy with the sound, re-record by pressing 9 
and the Master Code.  If you would like to hear the address again, press 8 for Play Address. 
 
If you accidentally press 9 but have not entered your master code and do not wish to record a new address, simply hang up the 
phone.  The address can be recorded from a local (in house) phone or a remote phone.  We suggest using a local phone for higher 
sound quality. 
 

¾  When the OmniPro II says "record address - beep" any previous address recorded on your system is erased.  Always 

verify that you have your name and address in your system if you have entered this function. 

 
¾  When recording the address, do not press any touch-tone keys on your phone until the second beep, indicating that 

recording is complete. This will cause improper operation when the system dials out.  The OmniPro II will think that the 
tone is a code being entered by the called party and it will stop talking.