Cisco Systems 3.2 Manuale Utente
4-4
Cisco Wireless LAN Controller Configuration Guide
OL-8335-02
Chapter 4 Configuring Controller Settings
Using the Configuration Wizard
Running the Configuration Wizard on the CLI
When the controller boots at factory defaults, the bootup script runs the configuration wizard, which
prompts the installer for initial configuration settings. Follow these steps to enter settings using the
wizard on the CLI:
prompts the installer for initial configuration settings. Follow these steps to enter settings using the
wizard on the CLI:
Step 1
Connect your computer to the controller using a DB-9 null-modem serial cable.
Step 2
Open a terminal emulator session using these settings:
•
9600 baud
•
8 data bits
•
1 stop bit
•
no parity
•
no hardware flow control
Step 3
At the prompt, log into the CLI. The default username is admin and the default password is admin.
Step 4
If necessary, enter reset system to reboot the unit and start the wizard.
Step 5
The first wizard prompt is for the system name. Enter up to 32 printable ASCII characters.
Step 6
Enter an administrator username and password, each up to 24 printable ASCII characters.
Step 7
Enter the service-port interface IP configuration protocol: none or DHCP. If you do not want to use the
service port or if you want to assign a static IP Address to the service port, enter none.
service port or if you want to assign a static IP Address to the service port, enter none.
Step 8
If you entered none in step 7 and need to enter a static IP address for the service port, enter the
service-port interface IP address and netmask for the next two prompts. If you do not want to use the
service port, enter 0.0.0.0 for the IP address and netmask.
service-port interface IP address and netmask for the next two prompts. If you do not want to use the
service port, enter 0.0.0.0 for the IP address and netmask.
Step 9
Enter the management interface IP Address, netmask, default router IP address, and optional VLAN
identifier (a valid VLAN identifier, or 0 for untagged).
identifier (a valid VLAN identifier, or 0 for untagged).
Step 10
Enter the Network Interface (Distribution System) Physical Port number. For the controller, the possible
ports are 1 through 4 for a front panel GigE port.
ports are 1 through 4 for a front panel GigE port.
Step 11
Enter the IP address of the default DHCP Server that will supply IP Addresses to clients, the
management interface, and the service port interface if you use one.
management interface, and the service port interface if you use one.
Step 12
Enter the LWAPP Transport Mode, LAYER2 or LAYER3 (refer to the Layer 2 and Layer 3 LWAPP
Operation chapter for an explanation of this setting).
Operation chapter for an explanation of this setting).
Step 13
Enter the Virtual Gateway IP Address. This address can be any fictitious, unassigned IP address (such
as 1.1.1.1) to be used by Layer 3 Security and Mobility managers.
as 1.1.1.1) to be used by Layer 3 Security and Mobility managers.
Step 14
Enter the Cisco WLAN Solution Mobility Group (RF group) name.
Step 15
Enter the WLAN 1 SSID, or network name. This is the default SSID that lightweight access points use
to associate to a controller.
to associate to a controller.
Step 16
Allow or disallow Static IP Addresses for clients. Enter yes to allow clients to supply their own IP
addresses. Enter no to require clients to request an IP Address from a DHCP server.
addresses. Enter no to require clients to request an IP Address from a DHCP server.
Step 17
If you need to configure a RADIUS Server, enter yes, and enter the RADIUS server IP address, the
communication port, and the shared secret. If you do not need to configure a RADIUS server or you want
to configure the server later, enter no.
communication port, and the shared secret. If you do not need to configure a RADIUS server or you want
to configure the server later, enter no.