Toshiba D-R17DTKB Manuale Utente
44
EN
Settings for External Equipment
Connection to External Equipment
Connect the external equipment using either the input
jacks, AV1, AV2 (Rear) or AV3 (Front). However, for
AV3 jacks, you have to select S-VIDEO input or
VIDEO input jacks depending on the connected
devices.
Use a commercially available Scart, S-Video or Video
cable and an Audio cable for this connection.
jacks, AV1, AV2 (Rear) or AV3 (Front). However, for
AV3 jacks, you have to select S-VIDEO input or
VIDEO input jacks depending on the connected
devices.
Use a commercially available Scart, S-Video or Video
cable and an Audio cable for this connection.
1
In stop mode, press [SETUP]. Select
“General Setting” using [
“General Setting” using [
U / D],
then press [ENTER/OK].
2
Select “Video” using [
U / D], then
press [ENTER/OK].
3
Select “Select Video” using [
U / D],
then press [ENTER/OK].
4
Select the input jack type to be used
using [
using [
U / D], then press
[ENTER/OK].
• If you want to use VIDEO input jack (Composite),
select “Video In”.
• If you want to use S-VIDEO input jack, select
“S-Video In”.
5
Press [SETUP] to exit.
Recording from External Equipment
Before recording from external equipment, see page
21 for connection instructions.
21 for connection instructions.
1
Turn the TV and the unit on, and
select the input of the TV to which
the unit is connected.
select the input of the TV to which
the unit is connected.
2
Press [OPEN / CLOSE
O] to open the
disc tray, then place the disc to
record on.
Press [OPEN / CLOSE
record on.
Press [OPEN / CLOSE
O] again to
close the disc tray.
3
Select the input terminal to which the
external equipment is connected.
(AV1, AV2, or AV3)
external equipment is connected.
(AV1, AV2, or AV3)
To use the input jacks on the back of the unit,
select the “AV1” or “AV2” position by pressing
[INPUT SELECT
select the “AV1” or “AV2” position by pressing
[INPUT SELECT
] or [PROG.
/
].
To use the input jacks on the front of this unit,
select “AV3” position by pressing
[INPUT SELECT
select “AV3” position by pressing
[INPUT SELECT
] or [PROG.
/
].
4
Select a recording mode using
[REC MODE].
[REC MODE].
Refer to “Recording Mode” on page 32.
5
Press [
I
REC] on the unit to start
recording.
6
Press the PLAY button on the
external recording component.
external recording component.
7
Press [
S (STOP)] on the unit to stop
recording.
Note
• During recording, if a signal other than PAL is
detected (such as NTSC), recording is paused.
• If you want to monitor the programme that you are
recording, make sure the device such as a Satellite
Box is turned off when it is connected to AV2.
Box is turned off when it is connected to AV2.
DVD-RW
DVD-RW
Video
DVD-RW
DVD-RW
VR
DVD-R
DVD-R
D
DVD+R
VD+RW
W
DVD+RW
D
DVD+R
VD+R
DVD+R
HDMI
Reset All
Reset All
TV Aspect
Select Video
Video Out
Select Video
Video Out
General Setting
Playback
Display
Display
Clock
Channel
DivX
Channel
DivX
Recording
Video
Select Video - AV3(Front)
Video In
S-Video In
S-Video In
DVD-RW
DVD-RW
Video
DVD-RW
DVD-RW
VR
DVD-R
DVD-R
D
DVD+R
VD+RW
W
DVD+RW
D
DVD+R
VD+R
DVD+R
E7J70BD_EN.book Page 44 Monday, May 7, 2007 3:31 PM