Lucent Technologies 8110M Manuale Utente

Note: The following installation procedures are applicable for all of 
the 8100 Series telephones. 

Use the 7-foot straight line cord that came with your telephone to 
connect the telephone to a modular jack, and, if you are using the 
8103, 8104, or 8111, you must connect the telephone with the power 
supply that comes in the box with the phone.

WARNING: Do not plug the handset cord into the line jack or the 
adjunct jack on the bottom of your telephone since it could damage 
your handset and the telephone.

1 Turn the telephone upside down so that you can see the bottom of 

the telephone. 

2 Plug one end of the line cord into the line jack on the bottom of the 

telephone. 

3 Feed the line cord through the line cord routing channel. 

4 Turn the telephone right-side up and place it on your desk or table. 

5 Plug one end of the coiled handset cord into the handset jack on 

the side of the telephone. 

6 Plug the other end of the handset cord into the handset. 

7 Hang up the handset. 

8 Do one of the following:

—

If you are using an 8101, 8102M, or 8110M, plug the free end 
of the line cord into a modular wall jack.

—

If you are using an 8103, 8104, or 8111, plug the free end of 
the line cord into the PHONE jack on the power supply. Then, 
plug the power supply cord into the LINE jack on the power 
supply and plug the other end of the power supply cord into 
the modular wall jack.

9 Lift the handset and listen for dial tone.

10 Set the Ringer Volume Control switch and the Tone Selectors to 

the settings you want.

Use the following directions to mount the telephone on a standard 
wallphone jack with mounting studs. 

1 You must reverse the handset tab (which holds the handset when 

you hang up). 

• Hold down the switchhook and slide the handset tab up and out of 

its slot. 

• Turn the tab so that the curved end is facing up.

• Insert the tab back into its slot.

2 Turn the telephone upside down so that you can see the bottom of 

the telephone. 

3 Remove the mounting base by pushing in on the triangle at the 

center of the large end of the base and then lifting the base off the 
telephone. 

4 Turn the base so the larger end is down.

5 Place the base on the wall-jack mounting studs and pull down 

until it is secure. 

6 Plug one end of the line cord into the line jack on the bottom of the 

telephone. 

Note: You may prefer to use an 8-inch line cord rather than the 7-
foot cord provided with the telephone. If you use the 7-foot cord, 
you will need to place it into the back of the telephone in its 
original coiled position.

7 Plug the free end of the line cord into the modular wall jack.

8 Plug one end of the coiled handset cord into the handset jack on 

the side of the telephone. 

9 Place the telephone against the base and push down so that the 

base locking tab slides into the slot at the top of the telephone. 

10 Push in on the triangle at the bottom center of the base to lock the 

bottom of the telephone into place. 

11 Plug the free end of the coiled handset cord into the handset and 

hang up the handset. 

12  Lift the handset and listen for dial tone. 

13 Set the Ringer Volume Control switch and Tone Selectors to the 

settings you want.

1 Remove the plastic cover, which fits over the designation card, by 

placing your finger in the finger slot on the right side of the 
telephone and lifting up.

2 Place the plastic cover aside, and remove the blank designation 

card from the telephone.

3 In the blank space next to the appropriate Programmable Dialing 

button, write or type the name, telephone number, or dialed 
feature that you want to store there. 

4 Place the designation card on the telephone. Replace the plastic 

cover over the card by fitting the cover’s bottom tabs into the slots 
on the telephone and pressing down, allowing the tabs on the top 
to snap into place.

If you have an 8110M or 8111 telephone, you may want to disable the 
Auto Answer button (

) so that it cannot be activated 

accidentally. Follow this procedure to remove the Auto Answer 
button and then cover the resulting opening.

Note: To complete this procedure, you will need the slot cover which 
is shipped in the box with the telephone. 

1 Press  so that the button is in the “up” position

2 Lift the button from its slot on the face of the telephone. (You will 

probably want to use a set of needlenose pliers for this task.) 

3 Take the slot cover (provided with the telephone) and place it in a 

horizontal position in the empty slot. Be sure that the cap is snug 
with the face of the telephone.

Note: The installation of adjunct equipment (such as the S201A 
Speakerphone or 500A Headset Adapter) with the 8102M or 8104 
telephone is different from installation with other telephones.

1 Plug one end of the adjunct cord into the adjunct equipment.

2 Plug the other end of the adjunct cord into the Adjunct jack on the 

rear of the 8102M or 8104 telephone.

3 Plug one end of the adjunct power cord into the Adjunct Power 

jack on the bottom of the 8102M or 8104 telephone.

4 Plug the free end of the adjunct power cord into the adjunct power 

supply.

To answer calls using the 500A Headset Adapter
Note: If a 500A headset adapter is connected to your 8102M or 
8104,you may use the handset or headset adapter to answer calls.

To answer a call with the headset adapter, press the 
On/Quiet button. (The green light next to the button goes on.) To 
mute the handset or headset adapter, you must hold down the
On/Quiet button. (The green light next to the button stays on for as 
long as the button is held down.) When you want the other party to 
hear you again, you can remove your finger from the On/Quiet 
button. (The light goes off.)

To end a call, press the Off button on the headset adapter.

To go off-hook to place a call, press the On/Quiet button and dial the 
number using the dial pad, press 

, or use the appropriate 

programmable dialing button. Flash works the same with the headset 
adapter as it would with a handset.

Press 

 on the 8102M or 8104. (Note that the green light next to 

the On/Quiet button on the headset adapter remains on, even though 
the call is on hold.) To retrieve the held call, you must press the Off 
button, and then within 2 seconds, press the On/Quiet button. (The 
red Hold light on the 8102M or 8104 goes off.) If you take more than 2 
seconds for this sequence of button presses, the call will be dropped.

Line jack
on telephone

LINE

PHONE

Power supply cord

Wall
jack

Line cord