Frigidaire FASG7073R ユーザーズマニュアル
Specifications
subject to change.
Front Load Laundry - Gas Steam Dryer
Frigidaire Affinity (All L Models)
Front Load Dryer Specifications
•
Product Shipping Weight (approx.) – 140 Lbs.
•
An electrical supply with grounded three-prong receptacle is
required. The power supply circuit must be installed in accordance
with current edition of National Electrical Code (ANSI/NFPA 70)
and local codes & ordinances. (Do not use same circuit as washer.)
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Amps @ 120 Volts = 7 Amps
•
Connected Load (kW Rating) @ 120 Volts = 0.5 kW
•
Equipped with 120V 3-wire power supply cord, approx. 60" long.
•
Always consult local and national electric, gas & plumbing codes.
•
Can be installed alone, with or without optional 15" Drawer Pedestal,
or stacked above matching Frigidaire® Affinity Washer, which requires
installation of optional Dryer Stacking Kit. (For installation details, refer
to instructions included with optional pedestal or stacking kit or on web.)
•
Can be built in with matching Frigidaire® Affinity Washer in under-
counter, recessed or closet installation. (Refer to Built-In Installations
on this page for cutout dimensions. For additional installation details,
refer to Product Installation Guide on web.)
•
Closet installation requires vented door with 2 unobstructed louvered
openings, minimum 60 sq. in. each, located 3" from top and bottom
of door. Full-length 120 sq. in. opening also acceptable. Allow
additional 1" clearance between fronts of units and closed door.
•
Do NOT install in area exposed to dripping water or outdoor weather
conditions; where gasoline or other flammables are kept or stored; or
where dryer comes in contact with curtains, drapes or anything that
will obstruct flow of combustion and ventilation air.
•
For garage installation, dryer MUST be located minimum 18" above floor.
•
Floor MUST be solid with 1" maximum slope. Do NOT install on
carpeted surface.
•
Dryer MUST exhaust to outside of building, NOT into any concealed
space.
•
Exhaust installation requires minimum 4"-diameter rigid or semi-rigid
metal duct with approved, unobstructed vent hood having swing-out
damper(s). If installing rigid metal duct (preferred), do not exceed
MAXIMUM venting run length of 64 ft., allow deductions for elbows
and vents. If installing semi-rigid metal duct, do not exceed MAXIMUM
venting run length of 8 ft., always allow deductions for elbows and
vents (Refer to Product Installation Guide on web for additional
information). Do NOT use flexible plastic or metal foil duct and use
shortest run possible.
•
Gas supply line should be 1/2" pipe and MUST have individual
shutoff valve.
•
Leveling legs supplied to level dryer properly and reduce excessive
noise and vibration.
•
Water inlet hose for steam setting connects to cold water supply
with “Y” connector and requires 3/4" clearance between back of unit
and wall.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.
Optional Accessories
•
Dryer Stacking Kit – (PN # STACKIT4X).
•
15" Classic Red Drawer Pedestal – (PN # CFPWD15R).
•
15" Classic Blue Drawer Pedestal – (PN # CFPWD15N).
•
15" Classic Silver Drawer Pedestal – (PN # CFPWD15A).
•
15" Classic White Drawer Pedestal – (PN # CFPWD15W).
•
Mobile Home Installation Kit – (PN # 137067200).
•
LP Gas Conversion Kit – (PN # PCK4200).
•
Drying Rack – (PN # 137067300).
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
FASG7073L 09/11
© 2011 Electrolux Home Products, Inc.
Printed in the U.S.A.
Front Load Dryers
FASG7073L R / N / A / W
7.0 Cu. Ft. Gas