Honeywell 2-Partitioned Security System ユーザーズマニュアル
– 13 –
5800 Series Transmitters Loop Designations
LOOP
1
5 8 0 2 M N
ENROLL AS "UR" OR "RF"
YOU MUST
ENROLL THIS
BUTTON
ENROLL THIS
BUTTON
LOOP 3
LOOP 1
LOOP 2
LOOP 4
LOOP
1
5808
ENROLL AS "RF"
5 8 0 4
ENROLL
AS "BR"
5 8 1 7
ENROLL AS "RF"
LOOP 1
(PRIMARY)
(PRIMARY)
LOOP 2
(AUX. CENTER)
(AUX. CENTER)
LOOP 3
(AUX. RIGHT)
(AUX. RIGHT)
LOOP 1
(MOTION)
(MOTION)
5 8 9 0
ENROLL AS "RF"
5 8 1 6
ENROLL AS "RF"
LOOP 2
(REED)
(REED)
LOOP 1
(TERMINALS)
(TERMINALS)
5 8 2 7
SET HOUSE CODE
5 8 2 7 B D
SET HOUSE CODE
5 8 1 6 M N
ENROLL AS "RF"
LOOP 2
(REED)
(REED)
LOOP 1
(TERMINALS)
(TERMINALS)
5 8 1 9
ENROLL AS "RF"
LOOP
2
(REED)
LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP 2
LOOP 3
(TERMINALS)
5 8 1 9 S ( W H S & B R S )
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 1
(INTERNAL
SHOCK
SENSOR)
(INTERNAL
SHOCK
SENSOR)
LOOP 3
(TERMINALS)
5 8 5 0 ( G B D )
ENROLL AS "RF"
(Green)
(Red)
(Yellow)
(Red)
(Yellow)
5 8 0 4 B D
ENROLL AS "BR"
LOOP 3
LOOP 1
LOOP 2
LOOP 4
SET
HOUSE
CODE
YOU MUST
ENROLL THIS
BUTTON
LOOP
1
5809
ENROLL AS "RF"
5 8 0 1
ENROLL AS "UR" OR "RF"
LOOP 3
LOOP 1
LOOP 2
LOOP 4
YOU MUST
ENROLL THIS
BUTTON
ENROLL THIS
BUTTON
•
•
••
•
•
••
•
•
•
• •
• •
•
•••
5800_trans_loop-V0
Note: For information on any transmitter not shown above, refer to the instructions accompanying that transmitter for
details regarding loop numbers, etc.
details regarding loop numbers, etc.
UL
The 5802MN, 5802MN2, 5804, 5804BD, 5814, 5816TEMP, 5819, 5819WHS & BRS, 5827BD,
and 5850 transmitters are not intended for use in UL installations.
and 5850 transmitters are not intended for use in UL installations.
PROMPT
EXPLANATION
XMIT TO CONFIRM
PRESS
✱TO SKIP
Confirmation Option: This prompt only appears if you answered “Yes” at the first prompt. The system
enters a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate
the loop input or button that corresponds to this zone. At any time during this step, you may press the [
enters a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate
the loop input or button that corresponds to this zone. At any time during this step, you may press the [
✱] key
on the keypad to save the serial and loop number combination without confirming.
Entd
A022-4063 1
Rcvd
A022-4064
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears. If the loop number does not match, it is also displayed.
at the left appears. If the loop number does not match, it is also displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display does not appear), press the [#] key twice and then enter or transmit the correct serial number.
display does not appear), press the [#] key twice and then enter or transmit the correct serial number.
10 ZT P RC In L
03 1 3C RF 1s
If the serial number transmitted does match the serial number entered, the system beeps 3 times and a
summary display appears, showing that zone’s programming. Note that an “s” indicates that a transmitter’s
serial number has been enrolled.
summary display appears, showing that zone’s programming. Note that an “s” indicates that a transmitter’s
serial number has been enrolled.
Press [
✱] to accept the zone information.