Hearth & Home Technologies Tucson (8700) ユーザーズマニュアル
HearthStone Quality Home Heating Products Inc
Tucson
Model #8700
10
O
WNER
’
S
I
NFORMATION
The installation must conform with local
codes or, in the absences of local codes, the
current National Fuel Gas Code, ANSI Z223.1
(NFPA 54) or CAN/CGA B149 Installation
Code. (Installer l’appareil selon les codes ou
règlements locaux, ou, en l’absence de tels
règlements, selon les Codes d’installation
CAN/CGA-B149.)Do not use this appliance
if any part has been under water.
Immediately call a qualified service
technician to inspect the heater and to
replace any part of the control system and
gas control that has been under water. (Ne
pas se servir de cet appareil s’il a été plongé
dans l’eau, complètement ou en partie.
Appeler un technicien qualifié pour inspector
l’appareil et remplacer toute partie du système
de contrôle et toute commande qui ont été
plongés dans l’lau.)
codes or, in the absences of local codes, the
current National Fuel Gas Code, ANSI Z223.1
(NFPA 54) or CAN/CGA B149 Installation
Code. (Installer l’appareil selon les codes ou
règlements locaux, ou, en l’absence de tels
règlements, selon les Codes d’installation
CAN/CGA-B149.)Do not use this appliance
if any part has been under water.
Immediately call a qualified service
technician to inspect the heater and to
replace any part of the control system and
gas control that has been under water. (Ne
pas se servir de cet appareil s’il a été plongé
dans l’eau, complètement ou en partie.
Appeler un technicien qualifié pour inspector
l’appareil et remplacer toute partie du système
de contrôle et toute commande qui ont été
plongés dans l’lau.)
D
AILY
O
PERATION
The Tucson gas-fired heater is easily
operated by the homeowner once installed
and adjusted by qualified service personnel.
The unit is controlled via the wall-mounted
thermostat during the heating season. Set the
thermostat to the desired room temperature
and the unit will cycle on and off as
required. By adjusting the variable output
control located on the gas control valve, the
rate of heat output can be varied to meet the
heating requirements of the season.
Choosing a low flame setting will result in
longer burn cycles at a reduced output, while
choosing a high flame setting will result in a
shorter, hotter burn cycle. Through trial and
error, the homeowner can select the
optimum flame size for their setting and
application.
During the summer non-heating season,
switch the wall thermostat to “OFF”, and
turn off the pilot. This will improve the
operated by the homeowner once installed
and adjusted by qualified service personnel.
The unit is controlled via the wall-mounted
thermostat during the heating season. Set the
thermostat to the desired room temperature
and the unit will cycle on and off as
required. By adjusting the variable output
control located on the gas control valve, the
rate of heat output can be varied to meet the
heating requirements of the season.
Choosing a low flame setting will result in
longer burn cycles at a reduced output, while
choosing a high flame setting will result in a
shorter, hotter burn cycle. Through trial and
error, the homeowner can select the
optimum flame size for their setting and
application.
During the summer non-heating season,
switch the wall thermostat to “OFF”, and
turn off the pilot. This will improve the
overall efficiency of the unit as the heat
from the pilot is wasted. When putting the
unit back into service, follow the lighting
instructions described on page 31.
When the unit is first lit, especially when
cool, it is normal to experience some
condensation on the inside of the window
glass. This condensation will burn off within
the first few minutes of operation. If
continuous condensation on the window
glass or dripping water from any part of the
unit or venting system (chimney) is noted,
immediately discontinue operation of the
unit and contact qualified service personnel.
from the pilot is wasted. When putting the
unit back into service, follow the lighting
instructions described on page 31.
When the unit is first lit, especially when
cool, it is normal to experience some
condensation on the inside of the window
glass. This condensation will burn off within
the first few minutes of operation. If
continuous condensation on the window
glass or dripping water from any part of the
unit or venting system (chimney) is noted,
immediately discontinue operation of the
unit and contact qualified service personnel.
R
OUTINE
M
AINTENANCE
AND
C
ARE
The Tucson requires minimal routine
maintenance and care. The unit should
always be cool and off when being cleaned.
maintenance and care. The unit should
always be cool and off when being cleaned.
C
LEANING
› WARNING: Do not clean the unit
when hot. The unit should receive
regular cleaning on, under, and around
the stove to prevent the buildup of dust
and lint. The exterior surfaces of the unit
can be cleaned using soap, water, and a
soft cloth. Do not use abrasive or
chemical cleaners and take care not to
scratch the glass or enamel finish (if so
equipped) when cleaning the unit. The
use of chemical wax based cleaners or
polishes are not recommended due to the
potential for discoloration or the enamel
when the residue of the cleaners or
polishes is exposed to heat.
regular cleaning on, under, and around
the stove to prevent the buildup of dust
and lint. The exterior surfaces of the unit
can be cleaned using soap, water, and a
soft cloth. Do not use abrasive or
chemical cleaners and take care not to
scratch the glass or enamel finish (if so
equipped) when cleaning the unit. The
use of chemical wax based cleaners or
polishes are not recommended due to the
potential for discoloration or the enamel
when the residue of the cleaners or
polishes is exposed to heat.