Hearth & Home Technologies Tucson (8700) ユーザーズマニュアル
HearthStone Quality Home Heating Products Inc
Tucson
Model #8700
14
U
NPACKING AND
I
NSPECTION
U
NPACK AND
I
NSPECT FOR
D
AMAGE
The Tucson is packaged by the manufacturer
to withstand shipment without damage.
However, damage can occur during transit
so take care to inspect for damage when
unpacking and installing the unit. If any
damage or missing parts are detected,
immediately contact your dealer. Do not
install or put into service a damaged or
incomplete heater.
Caution: The two top stones and grill are
NOT cemented or otherwise permanently
fastened in place! Carefully remove and set
aside the two stones and the grill. Use the
protective wrapping material to temporarily
protect the stones from chipping and damage
while the unit is inspected and installed.
Inspect the Tucson for visible or concealed
damage. The unit should appear to be square
and true. The stones should be whole and
without cracks, chips, or breakage. The
sheet metal parts should be smooth and free
of bends and dents. The enameled cast iron
should be free of chips or cracks. If visible
or concealed damage is found or suspected,
contact your dealer for instructions.
With the top stones and grill removed and
set aside, undo the lag bolts that fasten the
unit to the pallet. Take care not to mar or
chip the enameled legs. Lift the stove off the
pallet and set it into place.
The decorative ceramic fiber logs supplied
with the Tucson are contained within the
firebox. Always use great care when
handling the decorative ceramic fire logs as
they are fragile and subject to damage and
breakage if handled roughly. Open the
firebox door using a 1/8” allen wrench
screwdriver and inspect the logs for damage.
If a broken log is encountered, contact your
to withstand shipment without damage.
However, damage can occur during transit
so take care to inspect for damage when
unpacking and installing the unit. If any
damage or missing parts are detected,
immediately contact your dealer. Do not
install or put into service a damaged or
incomplete heater.
Caution: The two top stones and grill are
NOT cemented or otherwise permanently
fastened in place! Carefully remove and set
aside the two stones and the grill. Use the
protective wrapping material to temporarily
protect the stones from chipping and damage
while the unit is inspected and installed.
Inspect the Tucson for visible or concealed
damage. The unit should appear to be square
and true. The stones should be whole and
without cracks, chips, or breakage. The
sheet metal parts should be smooth and free
of bends and dents. The enameled cast iron
should be free of chips or cracks. If visible
or concealed damage is found or suspected,
contact your dealer for instructions.
With the top stones and grill removed and
set aside, undo the lag bolts that fasten the
unit to the pallet. Take care not to mar or
chip the enameled legs. Lift the stove off the
pallet and set it into place.
The decorative ceramic fiber logs supplied
with the Tucson are contained within the
firebox. Always use great care when
handling the decorative ceramic fire logs as
they are fragile and subject to damage and
breakage if handled roughly. Open the
firebox door using a 1/8” allen wrench
screwdriver and inspect the logs for damage.
If a broken log is encountered, contact your
dealer for replacement logs. Otherwise, set
the logs aside until called for during the
installation.
the logs aside until called for during the
installation.
H
EARTH
R
EQUIREMENT
/F
LOOR
P
ROTECTION
The Tucson may be placed on a non-
combustible surface or wood floor. For
placement of the Tucson on carpeting, vinyl
tile or other combustible materials, the
appliance shall be installed on a metal or
wood panel extending the full width and
depth of the appliance. Installations must
meet local codes.
placement of the Tucson on carpeting, vinyl
tile or other combustible materials, the
appliance shall be installed on a metal or
wood panel extending the full width and
depth of the appliance. Installations must
meet local codes.