Marantz PM-11S3 ユーザーズマニュアル

2

ENGLISH

The supplied remote control can be used to control marantz 

Integrated Amplifier and marantz Super Audio CD player.

• The remote control may not operate some products.

e

 Put the rear cover back on.

q

 Remove the rear lid in the 

direction of the arrow and 

remove it.

w

 Load the two batteries 

properly as indicated by 

the marks in the battery 

compartment.

• Insert the specified batteries in the remote control unit.

• Replace the batteries with new ones if the set does not 

operate even when the remote control unit is operated close 

to the unit. (The supplied batteries are only for verifying 

operation. Replace them with new batteries at an early date.)

• When inserting the batteries, be sure to do so in the proper 

direction, following the 

q and w marks in the battery 

compartment.

• To prevent damage or leakage of battery fluid:

• Do not use a new battery together with an old one.

• Do not use two different types of batteries.

• Do not attempt to charge dry batteries.

• Do not short-circuit, disassemble, heat or dispose of 

batteries in flames.

• Do not keep the battery in a place exposed to direct sunlight 

or in places with extremely high temperatures, such as near 

a heater.

• If the battery fluid should leak, carefully wipe the fluid off the 

inside of the battery compartment and insert new batteries.

• Remove the batteries from the remote control unit if it will 

not be in use for long periods.

• Used batteries should be disposed of in accordance with the 

local regulations regarding battery disposal.

• The remote control unit may function improperly if 

rechargeable batteries are used.

Point the remote control unit at the remote sensor when 

operating it.

• The set may function improperly or the remote control unit 

may not operate if the remote control sensor is exposed to 

direct sunlight, strong artificial light from an inverter type 

fluorescent lamp or infrared light.

• When using 3D video devices that transmit radio 

communication signals (such as infrared signals etc) 

between the various units (such as the monitor, 3D glasses, 

3D transmitter unit etc), the remote control unit may not 

operate due to interference from those radio communication 

signals. If this occurs, adjust the direction and distance of the 

3D communication for each unit, and check that the remote 

control unit operation is not affected by these signals.

30°

Approx. 26.2ft / 8 m

30°

• Before turning the power on

Check once again that all connections are correct and that 

there are no problems with the connection cables.

• Power is supplied to some of the circuitry even when the 

unit is set to the standby mode. When going on vacation or 

leaving home for long periods of time, be sure to unplug the 

power cord from the power outlet.

• About condensation

If there is a major difference in temperature between the 

inside of the unit and the surroundings, condensation (dew) 

may form on the operating parts inside the unit, causing the 

unit not to operate properly.

If this happens, let the unit sit for an hour or two with the 

power turned off and wait until there is little difference in 

temperature before using the unit.

• Cautions on using mobile phones

Using a mobile phone near this unit may result in noise. If 

that occurs, move the mobile phone away from this unit 

when it is in use.

• Moving the unit

Turn off the power and unplug the power cord from the 

power outlet. Next, disconnect the connection cables to 

other system units before moving the unit.

• About care

• Wipe the cabinet and control panel clean with a soft cloth.

• Follow the instructions when using a chemical cleaner.

• Benzene, paint thinner or other organic solvents as well as 

insecticide may cause material changes and discoloration 

if brought into contact with the unit, and should therefore 

not be used.

1.PM-11S3U_ENG_0521.indd   2

2012/05/21   19:03:26