Mitsubishi Electronics MR-J3 ユーザーズマニュアル
8 - 2
8. PARAMETER UNIT (MR-PRU03)
8.1 External appearance and key explanations
This section gives the external appearance and explanations of the keys.
PRU03
MON
DATA
PARAM
ALM/
DGN
DGN
TEST
Fn
SHIFT
ESC
7
8
9
D
E
F
4
5
6
A
B
C
1
2
3
0
1STEP
STOP
RESET
REV
FWD
Key
MON
DATA
PARAM
ALM/
DGN
DGN
TEST
Mode
k
e
y
Fn
SHIFT
ESC
0
9
F
STOP
RESET
REV
FWD
1STEP
Key explanations
to
Display
LCD (16 characters x 4 lines)
Used to display the following or others:
Parameter setting
Monitor
Monitor mode key
Used to display the monitor screen.
Used to display the monitor screen.
Alarm/diagnosis mode
Used to display the alarm/DO forced output/diagnosis selection
screen.
Parameter mode key
Used to display parameter selection screen.
Press this key while holding down the "SHIFT" key to display the
point table setting screen.
Used to display the alarm/DO forced output/diagnosis selection
screen.
Parameter mode key
Used to display parameter selection screen.
Press this key while holding down the "SHIFT" key to display the
point table setting screen.
Test operation mode key
Used to display the exit/JOG operation/positioning operation/motor-
less operation/DO forced output/single-step feed selection screen.
Used to display the exit/JOG operation/positioning operation/motor-
less operation/DO forced output/single-step feed selection screen.
O
perat
ion k
e
y
Function key
Used to perform various operations in the test operation mode.
Used to display the parameter range and point table setting range.
SHIFT key
Used to enter hexadecimal values. Press the "4" to "9" keys while
holding down the "SHIFT" key to enter A to F.
Press the " " keys while holding down the "SHIFT" key to move
to the previous or next screen.
Used to perform various operations in the test operation mode.
Used to display the parameter range and point table setting range.
SHIFT key
Used to enter hexadecimal values. Press the "4" to "9" keys while
holding down the "SHIFT" key to enter A to F.
Press the " " keys while holding down the "SHIFT" key to move
to the previous or next screen.
ESC key
Used to display the screen at one step upper hierarchical level. (not
the pervious screen)
Used to display the setting selection screen (the initial screen) of the
monitor mode.
Scroll key
Used to move the cursor across the screen or scroll the screen.
Used to display the screen at one step upper hierarchical level. (not
the pervious screen)
Used to display the setting selection screen (the initial screen) of the
monitor mode.
Scroll key
Used to move the cursor across the screen or scroll the screen.
Press this key while holding down the "SHIFT" key to move to the
previous or next screen.
Used to change parameter No. or point table No.
Used to change parameter No. or point table No.
En
te
r k
e
y
Forward rotation key
Used to start the forward rotation in the test operation mode (JOG
operation/positioning operation).
Used to start the forward rotation in the test operation mode (JOG
operation/positioning operation).
Symbol key/reverse rotation key
Used to start the reverse rotation in the test operation mode (JOG
operation/positioning operation).
Used together with the "SHIFT" key to enter negative values. To exit
the negative value entry mode, press the "SHIFT" key again and
press the "-" key. ("-" disappears.)
Stop/reset key
Used to stop temporarily in the JOG operation/positioning
operation/single-step feed.
The "RESET" key is valid when the "Fn" key is not pressed (i.e. at a
stop).
Used to reset alarms or alarm history, or clear cumulated monitor
data or inputs.
Normal operation cannot be stopped with this key.
Enter key
Used to determine the selection, numerical values, etc.
Used to determine to exit the test operation mode, or enter the
motor-less operation.
Used to switch ON/OFF in the DO output screen.
Used to start the reverse rotation in the test operation mode (JOG
operation/positioning operation).
Used together with the "SHIFT" key to enter negative values. To exit
the negative value entry mode, press the "SHIFT" key again and
press the "-" key. ("-" disappears.)
Stop/reset key
Used to stop temporarily in the JOG operation/positioning
operation/single-step feed.
The "RESET" key is valid when the "Fn" key is not pressed (i.e. at a
stop).
Used to reset alarms or alarm history, or clear cumulated monitor
data or inputs.
Normal operation cannot be stopped with this key.
Enter key
Used to determine the selection, numerical values, etc.
Used to determine to exit the test operation mode, or enter the
motor-less operation.
Used to switch ON/OFF in the DO output screen.
Nu
m
e
ric
al
ke
y
Numerical keys
Used to enter parameter No., setting values, etc.
Press the "4" to "9" keys while holding down the "SHIFT" key to enter
A to F.
Used to enter parameter No., setting values, etc.
Press the "4" to "9" keys while holding down the "SHIFT" key to enter
A to F.
Decimal point key
Used to enter a decimal point.
Used to start the single-step feed.
Used to enter a decimal point.
Used to start the single-step feed.
T
est
Op
erat
io
n
key