Fantom Vacuum VPW43H ユーザーズマニュアル

4. Insert the handle into the handle 

bracket and secure with the two (2) 

screws provided. (Fig. 4)

Fig. 4

5. Slide the top brace over the legs and 

insert the handle assembly onto the 

top of the legs. Secure the handle 

assembly to the legs with the two (2) 

screws provided. (Fig. 5)

Fig. 5

6. Slide the top brace down the legs 

until it reaches the top of the 

pressure washer. Secure the top 

brace to the pressure washer unit 

with the two (2) screws provided. 

(Fig. 6)

Fig. 6

7. To attach the wheels to the support 

brackets, just push them in until they 

lock in place. (Fig. 7)

Fig. 7

8. To attach the front support to the 

pressure washer unit, place it under 

the front of the unit in the mark 

provided.  Push it in until it snaps into 

place. Then secure it to the pressure 

washer with the screw (1) provided. 

(Fig. 8)

Fig. 8

9. When the unit is finally assembled, it 

should look like the illustration below. 

(Fig. 9)

Fig. 9

Once all the desired attachments and 

the high pressure hose are attached to 

the pressure washer, you can connect 

the garden hose to the unit.

1. Attach the male adapter (supplied) to 

the water intake connector on the left 

hand side of the unit. (Fig. 13)

2. Attach the female hose coupling to 

the garden hose. (Fig. 13)

3. Connect the female hose coupling to 

the male adapter making sure that it 

is tightly secured in place. (Fig. 13)

Fig. 13

4. After all the connections have been 

and 

BEFORE you plug the pressure 

washer into an electrical outlet, open 

the water supply and press on the 

trigger switch in order to remove any 

air which may be in the hose or 

pump. Continue to press on the 

trigger switch until you get a constant 

flow of water coming out of the trigger 

gun. Allow water to flow for 30 

seconds.

5. Once this is accomplished, stop 

pressing the trigger switch. Engage 

the safety lock on the trigger

6. Ensure that the "On/Off" switch, at 

the rear of the unit, is on the "Off" 

position, then plug the unit into an 

electrical outlet and turn the unit to 

the "On" position.

7. Now you are ready to use the 

pressure washer. Disengage the 

safety lock and depress the trigger on 

the trigger gun.

Low 
pressure 
water inlet

3. Once the high pressure hose is 

connected to the trigger gun, you can 

attach any of the lances and 

accessories that you desire. To 

attach either of the lances or the 

brush to the trigger gun, hold the 

trigger gun in your left hand insert the 

desired lance or the brush and push 

it in all the way into the connector on 

the trigger gun and turn it clockwise 

60° until it locks in place. To remove 

the attachment, push down on the 

attachment and turn counter-

clockwise 60° and then pull out.

Make sure that the attachments are 

securely locked in place before use. 

(Fig. 12)

Fig. 12

2. Then attach the other end of the high 

pressure hose to the high pressure 

hose connector on the trigger gun. 

(Fig. 11)

Fig. 11

Once the pressure washer is 

assembled to the trolley, you are ready 

to use the unit.

1. While facing the front side of the unit 

attach the high pressure hose to the 

high pressure output connector on 

the right side of the unit. Twist on 

tight to avoid leakage. (Fig. 10)

Fig. 10

High 
pressure 
output fitting