Adder Technology Switch ユーザーズマニュアル
54
Network Settings
The Network Settings panel allows you to change network related parameters.
Each parameter will be explained below. Once applied, the new network
settings will immediately come into effect.
Note: The initial IP configuration is usually done directly at the host system
using the special procedure described in
Each parameter will be explained below. Once applied, the new network
settings will immediately come into effect.
Note: The initial IP configuration is usually done directly at the host system
using the special procedure described in
However you can also connect to the SmartView World using its pre-configured
IP settings.
Note: Changing the network settings of SmartView World might result in losing
connection to it. In case you change the settings remotely make sure all the
values are correct and you still have an option to access the IP section.
IP settings.
Note: Changing the network settings of SmartView World might result in losing
connection to it. In case you change the settings remotely make sure all the
values are correct and you still have an option to access the IP section.
IP auto configuration
With this option you can control if the SmartView World should fetch it’s
network settings from a DHCP or BOOTP server. For DHCP you have to enter
dhcp and for BOOTP supply bootp
accordingly. If you specify none then IP
autoconfiguration is disabled.
With this option you can control if the SmartView World should fetch it’s
network settings from a DHCP or BOOTP server. For DHCP you have to enter
dhcp and for BOOTP supply bootp
accordingly. If you specify none then IP
autoconfiguration is disabled.
IP auto configuration timeout
Time within a DHCP/BOOTP server is
expected to respond to the SmartView
World DHCP/BOOTP client request. If
there is no response, the last known IP
settings will be used to configure the
SmartView World.
Time within a DHCP/BOOTP server is
expected to respond to the SmartView
World DHCP/BOOTP client request. If
there is no response, the last known IP
settings will be used to configure the
SmartView World.
IP address
IP address in the usual dot notation.
IP address in the usual dot notation.
Subnet mask
The net mask of the local network.
The net mask of the local network.
Gateway IP address
In case the SmartView World should be
accessible from networks other than the
local one, this IP address must be set to
the local network router’s IP address.
In case the SmartView World should be
accessible from networks other than the
local one, this IP address must be set to
the local network router’s IP address.
Primary DNS Server IP address
IP address of the primary Domain Name Server in dot notation. This option may
be left empty, however the SmartView World won’t be able to perform name
resolution.
IP address of the primary Domain Name Server in dot notation. This option may
be left empty, however the SmartView World won’t be able to perform name
resolution.
Secondary DNS Server IP address
IP address of the secondary Domain Name Server in dot notation. It will be used
in case the Primary DNS Server can’t be contacted.
IP address of the secondary Domain Name Server in dot notation. It will be used
in case the Primary DNS Server can’t be contacted.
Primary Time Server
IP address of the primary NTP (Network Time Protocol) compliant timeserver
in dot notation. The SmartView World will synchronize its own absolute time
with the timeserver’s one. This is important for writing log entries and for the
Dynamic DNS Service.
IP address of the primary NTP (Network Time Protocol) compliant timeserver
in dot notation. The SmartView World will synchronize its own absolute time
with the timeserver’s one. This is important for writing log entries and for the
Dynamic DNS Service.
Secondary Time Server
IP address of the secondary NTP compliant timeserver in dot notation. It will be
used in case the Primary Time Server can’t be contacted.
IP address of the secondary NTP compliant timeserver in dot notation. It will be
used in case the Primary Time Server can’t be contacted.
Remote Console & HTTPS port
Port number at which the SmartView World Remote Console server and HTTPS
server are listening. If left empty the default value will be used.
Port number at which the SmartView World Remote Console server and HTTPS
server are listening. If left empty the default value will be used.
HTTP port
Port number at which the SmartView World HTTP server is listening. If left empty
the default value will be used.
Port number at which the SmartView World HTTP server is listening. If left empty
the default value will be used.
Telnet port
Port number at which the SmartView World Telnet server is listening. If left
empty the default value will be used.
Port number at which the SmartView World Telnet server is listening. If left
empty the default value will be used.
Bandwidth limitation
The maximum network traffic generated through the SmartView World Ethernet
device. Unit is Kbit/s.
The maximum network traffic generated through the SmartView World Ethernet
device. Unit is Kbit/s.
Disable Setup Protocol
With this option you may exclude the SmartView World from setup protocol.
With this option you may exclude the SmartView World from setup protocol.