Marantz AV8003 ユーザーガイド

ENGLISH

Video settings are made as follows.

 Select 

“4. VIDEO  SETUP” from the MAIN 

MENU with the 

3/4 cursor buttons and press 

the ENTER button.

        4 . V I D E O   S E T U P

V I D E O   C O N V E R T

T V - A U T O    

: D I S A B L E

O S D     I N F O         : E N A B L E
C O N P O N E N T   I / P : D I S A B L E
H D M I   O U T           : O U T P U T 1
H D M I   A S P E C T     : T H R O U G H
H D M I   O U T 1   R E S : A U T O
H D M I   O U T 2   R E S : A U T O
C O M P   O U T 2         : M A I N

R E T U R N              

N E X T

 

E X I T

  Select the desired menu with the 

3/4 cursor 

buttons and press the ENTER button.

This unit is equipped to convert video signals for 
monitor output.
This section explains how to set up conversion for 
each type of video input.

  Select “4. VIDEO SETUP” from the MAIN 

MENU with the 

3 / 4 cursor buttons and press 

the ENTER button.

  Select “VIDEO CONVERT” with the 

3 / 4 cursor 

buttons and press the ENTER button.

        V I D E O   C O N V E R T

      T V         :    

A N A & H D M I

      D V D       :     A N A & H D M I
      V C R 1     :     A N A & H D M I
      D S S       :     A N A & H D M I
      T A P E     :     A N A & H D M I
      C D / R     :     A N A & H D M I
      A U X       :     A N A & H D M I

R E T U R N    

 

         

E X I T

  Select “FUNCTION” with the 

3 / 4 cursor 

buttons and set the video conversion mode 
with the 

1 / 2 cursor buttons

This mode both up-converts and down-converts 
analog video signals (Composite Video, S-Video, 
Component Video). Furthermore, it up-converts 
from analog video signal to HDMI. (It cannot down-
convert from HDMI digital video signals to analog 
video signals.)

This mode both up-converts and down-converts 
analog video signals (Composite Video, S-Video, 
Component Video). It does not up-convert to 
HDMI.

OFF:
This mode turns off all conversion features.

•  For details on video convert feature, see page 39.

Select the TV AUTO ON/OFF function to enable 
or disable with the 

1 or 2 cursor buttons. (refer to 

page 46)

Select the OSD information function to “ENABLE” 
or “DISABLE” with the 

1 or 2 cursor buttons.

If you select “ENABLE”, this unit will display the 
status of the feature (Volume up/down, input 
select, etc..) on the monitor. If you do not desire 
this information, select “DISABLE”.

• OSD information is not output to Monitor Output 

of HDMI and Component Video. However, OSD 
information is output if the Video Convert function 
is used to output Video or S-Video video signals to 
Monitor Out of HDMI and Component Video. 

  For details, refer to“VIDEO CONVERT”on page 39.

Set whether or not to convert 480i/576i signals 
to 480p/576p signals when outputting the analog 
video input signal input from the COMPOSITE 
terminals, S-VIDEO terminals, or COMPONENT 
terminals.
Select “ENABLE” or “DISABLE.”

DISABLE: Do not convert

ENABLE: Convert

This setting is enabled only when VIDEO CONVERT 
is set to other than OFF.

This setting is for selecting which output terminal, 
OUTPUT1 or OUTPUT2, to output the signal to. 
Select the output destination with the 

1 / 2 cursor 

buttons.

To use the remote controller (RC2001) to change 
the HDMI OUT setting, press the HOME button, 
then the AMP button, and press the < / > button 
until 002 is displayed. After HDMI 1 or HDMI 2 is 
displayed on the remote controller, press the HDMI 
1 or HDMI 2 button to switch between them. 

=

Set HDMI ASPECT in accordance with the screen 
size of the television connected to this unit.
Select 16:9NORM or THROUGH using the 

1 or 2 

cursor buttons.

Output is in the same screen size as the input.

Output includes black bands on the left and right of 
the television screen.

•  This setting is enabled only when a 480i/576i signal 

is input and HDMI RESOLUTION is set to other 
than THROUGH, or when a 480p/576p signal is 
input.

• The aspect ratio cannot be changed when the input 

video signal is 720p or 1080i.

• This setting depends on network settings when a 

network is selected.

Selects the resolution of the video signal output 
from the HDMI terminal of this unit.
Select from the following using the 

1 or 2 cursor 

buttons.
THROUGH  ↔  480/576p  ↔  720p  ↔  1080i  ↔ 
1080p ↔ AUTO ↔ THROUGH

Sets an appropriate resolution for a television that 
is connected using HDMI.
(If connected by converting to DVI, the output is 
480p/576p)

The output is same resolution as that input.

The output is 480p/576p.

The output is 720p.

The output is 1080i.

The output is 1080p.

• The resolution cannot be changed when the input 

video signal is 720p or 1080i.

• The resolution depends on the network settings 

when a network is selected.

•  Signals are not output when connected to a monitor 

that does not support HDCP.

This setting is for selecting whether to output the 
images for the main zone or the images for the 
zone system to the COMPONENT MONITOR 
OUT 2 terminal. Select the output destination 
between MAIN and ZONE A with the 

1 / 2 cursor 

buttons.

• When ZONE A is selected, video signals converted 

from the MONITOR OUT 2 terminal are not 
output.

After you complete this portion of the setup, move 
cursor to “RETURN” with the 

3, 4, 1 and 2 cursor 

buttons and press the ENTER button.

AV8003N.indb   33

AV8003N.indb   33

08.4.28   10:49:20 AM

08.4.28   10:49:20 AM