Milwaukee 6232-6 band saw kit ユーザーズマニュアル

Grounded Tools: Tools with Three Prong Plugs
Tools marked “Grounding Required” have a three 
wire cord and three prong grounding plug. The 
plug must be connected to a properly grounded 
outlet (See Figure A). If the tool should electrically 
malfunction or break down, grounding provides a 
low resistance path to carry electricity away from 
the user, reducing the risk of electric shock.
The grounding prong in the plug is connected 
through the green wire inside the cord to the 
grounding system in the tool. The green wire in the 
cord must be the only wire connected to the tool's 
grounding system and must never be attached to 
an electrically “live” terminal.
Your tool must be plugged into 
an appropriate outlet, properly 
installed and grounded in accord-
ance with all codes and ordinances. 
The plug and outlet should look like 
those in Figure A.

Double Insulated Tools: 
Tools with Two Prong Plugs
Tools marked “Double Insulated” do not require 
grounding. They have a special double insula-
tion system which satisfi es OSHA requirements 
and complies with the applicable standards of 
Underwriters Laboratories, Inc., 
the Canadian Standard Asso-
ciation and the National Elec-
trical Code. Double Insulated 
tools may be used in either of 
the 120 volt outlets shown in 
Figures B and C.

Grounded tools require a three wire extension 
cord. Double insulated tools can use either a two 
or three wire extension cord. As the distance from 
the supply outlet increases, you must use a heavier 
gauge extension cord. Using extension cords with 
inadequately sized wire causes a serious drop in 
voltage, resulting in loss of power and possible tool 
damage. Refer to the table shown to determine the 
required minimum wire size.
The smaller the gauge number of the wire, the 
greater the capacity of the cord. For example, a 14 
gauge cord can carry a higher current than a 16 
gauge cord. When using more than one extension 
cord to make up the total length, be sure each cord 
contains at least the minimum wire size required. 
If you are using one extension cord for more than 
one tool, add the nameplate amperes and use the 
sum to determine the required minimum wire size.

Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be 

sure it is marked with the suffi x “W-A” (“W” in 
Canada) to indicate that it is acceptable for outdoor 
use.

• Be sure your extension cord is properly wired 

and in good electrical condition. Always replace a 
damaged extension cord or have it repaired by a 
qualifi ed person before using it.

• Protect your extension cords from sharp objects, 

excessive heat and damp or wet areas.

* Based on limiting the line voltage drop to fi ve volts at 

150% of the rated amperes.

25'

50'

75'

100'

150'

0 - 2.0

2.1 - 3.4
3.5 - 5.0
5.1 - 7.0

7.1 - 12.0

12.1 - 16.0
16.1 - 20.0

18
18
18
18
16
14
12

18
18
18
16
14
12
10

18
18
16
14
12
10

--

18
16
14
12
10

--
--

16
14
12
12

--
--
--

Blades and Blade Selection
The blade dimensions required for the band saws 
are: .020" thickness, 1/2" width and 44-7/8" in 
length. The special .020" thickness reduces fl exure 
fatigue and provides maximum tooth life. To maxi-
mize cutting life, use a blade with the correct pitch 
(teeth per inch) for the specifi c cutting job.
Blades are available in several pitches. To select the 
proper blade, three factors should be considered: 
The size, shape, and type of material to be cut.
The following suggestions are for selecting the 
right blade for various cutting operations. Keep in 
mind that these are broad guidelines and that blade 
requirements may vary depending upon the specifi c 
size, shape and type of material to be cut. Gener-
ally, soft materials require coarse pitch blades and 
hard materials require fi ne pitch blades. Use coarse 
pitch blades for thick work and fi ne pitch blades for 
thin work. It is important to keep at least three teeth 
in the cut (see "Typical Application").

4. To install a new blade, with the pulleys facing up, 

insert the blade between the rollers and the faces 
of the guides, making sure that the teeth on the left 
side of the tool point towards the rear of the tool. 

5. With one hand, hold the blade in place between 

the rollers and the guides and use the other hand 
to position the blade around the pulleys. Be sure 
that the blade lies freely within the guard channel 
before starting the tool motor.

6.  Turn the tension lock handle 180° clockwise to lock 

the position. This will secure the blade on the pulleys.

Blade LED (Cat. No. 6232-20)
To line-up a cut or light-up the workpiece, use the 
LED On/Off Switch.

Adjusting the 3-Position Material Guide
1. Unplug the tool.
2. Press in the guide adjustment button and slide 

the material guide to the desired position detent.

• For tough stock 1/2" to 3-3/8" in 

diameter or width (available in 
carbon steel only).

• For tough stock 3/8" to 1" in 

diameter or width (available in 
carbon steel only).

• For tough stock 3/16" up to 

4-3/4" in diameter or width.

• For tough stock 5/32" to 3/4" in 

diameter or width.

• For thin-wall tubing and thin 

sheets heavier than 21 gauge.

• For thin-wall tubing and thin 

sheets heavier than 21 gauge.

6 Teeth per Inch

8 Teeth per Inch

10 Teeth per Inch

14 Teeth per Inch

18 Teeth per Inch

24 Teeth per Inch

Changing Blades
1. UNPLUG THE TOOL BEFORE REMOVING OR 

INSTALLING BLADES. 

2. Turn the tension lock handle located on the front 

of the saw 180° counterclockwise. This releases 
the tension on the blade for easy removal. 

3. Remove the blades from the pulley fi rst and then 

from the guides.

Two Speed Switch (Cat. No. 6238-20)
MILWAUKEE Two-Speed Band Saws have a speed 
change switch located on top of the handle. To 
change speeds, stop the motor and slide the speed 
change switch to "HI" or "LO" as indicated on the 
tool. For cutting problem materials, use "LO" speed. 
Never change from one speed to the other while 
the motor is running.

Speed Dial (Cat. No. 6232-20)
MILWAUKEE Variable Speed Band Saws have a 
speed dial located on the side of the handle to set 
the maximum speed. Rotate the speed dial to “4” 
for maximum speed, “1” for minimum speed.

Starting and Stopping
1. To start the tool, grasp both handles fi rmly and 

pull the trigger.

 Improperly connecting the 

grounding wire can result in the risk of elec-
tric shock. Check with a qualifi ed electrician 
if you are in doubt as to whether the outlet is 
properly grounded. Do not modify the plug 
provided with the tool. Never remove the 
grounding prong from the plug. Do not use 
the tool if the cord or plug is damaged. If 
damaged, have it repaired by a MILWAUKEE 
service facility before use. If the plug will not 
fi t the outlet, have a proper outlet installed by 
a qualifi ed electrician.