Whirlpool wgd6600 ユーザーガイド

Use the Air Only Modifier for items that require drying without heat 
such as rubber, plastic, and heat-sensitive fabrics. This table shows 
examples of items that can be dried using Air Only.

Foam rubber - pillows, padded bras, stuffed toys

20 - 30

Plastic - Shower curtains, tablecloths

20 - 30

Rubber-backed rugs

40 - 50

Olefin, polypropylene, sheer nylon

10 - 20

*Reset cycle to complete drying, if needed.

■

Check that coverings are securely stitched.

■

Shake and fluff pillows by hand periodically during the cycle.

■

Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Air Only is not available with Automatic Cycles.

You can customize your cycles by selecting options.

On some models, select Drum Light to turn on the light inside the 
dryer drum. During a cycle, if Drum Light is selected, the drum light 
turns on and will remain on until DRUM LIGHT is pressed again, the 
door is opened and closed, or the door is left open for 5 minutes.

When the dryer is not running, the drum light will turn on when 
DRUM LIGHT is pressed or the dryer door is opened, and it will 
remain on until the dryer door has been open for 5 minutes, the 
dryer door is closed or DRUM LIGHT is pressed again. 

Press DRUM LIGHT at any time to turn the drum light ON or OFF.

The WRINKLE SHIELD™ setting helps keep wrinkles from forming 
when you cannot unload the dryer promptly at the end of a cycle. 
During this option, the dryer stops tumbling and then tumbles again 
for a brief period.

■

Press the WRINKLE SHIELD™ setting to get up to 120 minutes 
of heat-free, periodic tumbling at the end of a cycle.

■

Stop the WRINKLE SHIELD™ setting at any time by pressing 
WRINKLE SHIELD™ setting or opening the dryer door.

■

For the Perm Press/Casual Cycle, the WRINKLE SHIELD™ 
setting is preset to ON. The other Automatic Cycles will retain 
the WRINKLE SHIELD™ setting. For example, if you select the 
WRINKLE SHIELD™ setting in the Normal cycle, the WRINKLE 
SHIELD™ setting will be on the next time you select the Normal 
cycle.

NOTE: If you do not select the WRINKLE SHIELD™ setting, the 
dryer stops after cool down.

Select the Damp Dry Signal to alert you that your clothes are 
approximately 80% dry. This is useful when you want to remove 
lightweight items in a mixed load to avoid overdrying or remove 
partially dry items that may need ironing.

The Damp Dry Signal is useful when drying bedsheets/linens in a 
mixed load. When the signal goes off, open the door to stop the 
dryer, rearrange the load inside the dryer, close the door, and restart 
the dryer to finish the drying cycle. Rearranging the load will aid in 
the drying process.

NOTE: The Damp Dry Signal is available only with the Automatic 
Cycles.

The End of Cycle Signal produces an audible sound when the drying 
cycle is finished. Promptly removing clothes at the end of the cycle 
reduces wrinkling.

Press END OF CYCLE SIGNAL until the desired volume (Loud, Soft, 
or Off) is selected.

NOTE: When the WRINKLE SHIELD™ setting is selected and the 
End of Cycle Signal is on, a tone sounds every 5 minutes until the 
clothes are removed, or the WRINKLE SHIELD™ setting ends.

You can change Automatic and Timed Cycles, Modifiers, and 
Options anytime before pressing Start. 

■

Three short tones sound if an unavailable combination is 
selected. The last selection will not be accepted.

1. Press PAUSE/CANCEL twice.

2. Select the desired cycle and options.

3. Press START. The dryer starts at the beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the 
cycle, the dryer automatically shuts off.

You can change an Option or Modifier anytime before the selected 
Option or Modifier begins.

1. Press PAUSE/CANCEL once.

2. Select the new Option and/or Modifiers.

3. Press START to continue the cycle.

NOTE: If you happen to press PAUSE/CANCEL twice, the program 
clears and your dryer shuts down. Restart the selection process.

If all of your loads on all Auto Dry cycles are consistently not as dry 
as you would like, you may change the preset Dryness Level 
settings to increase the dryness. This change will affect all of your 
Auto Dry cycles.