GE ZTD910 ユーザーズマニュアル
4
Design Information
Warming Drawer
Advance
Planning
Planning
• The drawer may be installed below a
countertop, a cooktop, a single or double
oven and side by side using 2 drawers.
oven and side by side using 2 drawers.
• The warming drawer can be installed below
approved cooktops. Allow 2" min. clearance
from bottom of cooktop burner box to top
of warming drawer cutout. See page 5.
from bottom of cooktop burner box to top
of warming drawer cutout. See page 5.
• The warming drawer can be installed below
approved ovens. Allow a 2" min. clearance
between cutouts. Additional clearances may
be required. See page 6.
between cutouts. Additional clearances may
be required. See page 6.
IMPORTANT - (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
MUST BE PROPERLY GROUNDED.
Do not use an extension cord or adapter plug
with this appliance. Follow National electrical
codes or prevailing local codes and ordi-
nances.
with this appliance. Follow National electrical
codes or prevailing local codes and ordi-
nances.
This warming drawer must be supplied with
120V, 60Hz, and connected to an individual,
properly grounded branch circuit, and
protected by a 15 or 20 amp circuit breaker or
time delay fuse.
120V, 60Hz, and connected to an individual,
properly grounded branch circuit, and
protected by a 15 or 20 amp circuit breaker or
time delay fuse.
• A properly grounded 3-prong receptacle
should be located within reach of the
drawers’ 56” long power cord.
drawers’ 56” long power cord.
• Locate the receptacle in an adjacent cabinet.
– within 42” of the right side or,
– within 16” of the left side or,
– A recessed receptacle may be located on
– within 16” of the left side or,
– A recessed receptacle may be located on
the right side of the cutout, 7” from the
back of the cabinet. In this location, the
excess power cord should be coiled and
secured to the warming drawer side with
the power cord clip.
back of the cabinet. In this location, the
excess power cord should be coiled and
secured to the warming drawer side with
the power cord clip.
• When two warming drawers are installed
side to side, they can operate from the same
receptacle.
receptacle.
IMPORTANT: (Please read carefully).
The power cord of this appliance is equipped
with a three-prong (grounding) plug that
mates with a standard three-prong grounding
wall receptacle to minimize the possibility of
electric shock. The customer should have the
wall receptacle and circuit checked by a
qualified electrician to make sure the recep-
tacle is properly grounded and has the correct
polarity.
• Where a standard two-prong wall receptacle
The power cord of this appliance is equipped
with a three-prong (grounding) plug that
mates with a standard three-prong grounding
wall receptacle to minimize the possibility of
electric shock. The customer should have the
wall receptacle and circuit checked by a
qualified electrician to make sure the recep-
tacle is properly grounded and has the correct
polarity.
• Where a standard two-prong wall receptacle
is encountered, it is the personal responsibil-
ity and obligation of the customer to have it
replaced with a properly grounded three-
prong wall receptacle.
ity and obligation of the customer to have it
replaced with a properly grounded three-
prong wall receptacle.
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
DO NOT USE AN EXTENSION CORD.
remove the third (ground) prong from the
power cord.
DO NOT USE AN EXTENSION CORD.
Grounding
the
Appliance
the
Appliance
• Electrical power cord is located on the right
side of the warming oven. Locate the outlet
within reach of the 56” long power cord in
an adjacent cabinet, within 42” of the right
side or 16” from the left side of the cutout. A
recessed receptacle can be installed on the
right side of the cutout, 7” max. from the
rear of cabinet.
within reach of the 56” long power cord in
an adjacent cabinet, within 42” of the right
side or 16” from the left side of the cutout. A
recessed receptacle can be installed on the
right side of the cutout, 7” max. from the
rear of cabinet.
Drill 1-1/2" Hole
For Power Cord For
Left or Right Side
Outlet Location
For Power Cord For
Left or Right Side
Outlet Location
Recessed
Receptacle 7"
Max. From Rear
on Right Side.
Receptacle 7"
Max. From Rear
on Right Side.