Omnitron miConverter GX/T 1239-0-3 ユーザーズマニュアル
製品コード
1239-0-3
miConverter
miConverter
TM
Miniature Gigabit Ethernet media converter
Supports 1000BASE-T, 1000BASE-X and the
IEEE 802.3 specification
Plug-and-Play capability
USB power via optional Power Adapter Cable
Supports Full/Half-Duplex fiber optic auto-negotiation
Multimode and single-mode fiber options
LED indicators for UTP and fiber status
Domestic, Universal and
Country/Region specific
power
supply options
Wall-mount with optional mounting brackets or an
18-Module Powered Chassis
Small and lightweight (5 ounces)
Cost-effective
Commercial (0 to 50ºC), wide (-40º to 60ºC), extended
(-40º to 75º C) and industrial (-40º to 85ºC) temperature
ranges
Lifetime Warranty and free 24/7 Technical Support
miConverter
GX/T
10/100/1000BASE-T to 1000BASE-X Ethernet Media Converter
The miConverter GX/T is a miniature 10/100/1000BASE-T UTP
copper to 1000BASE-X fiber media converter that supports
jumbo frames up to 10,240 bytes. The miConverter GX/T
provides cost-effective fiber connectivity from Ethernet switches
to diagnostic equipment, desktop and laptop computers.
The GX/T features Small Form Pluggable (SFP) transceivers
The GX/T features Small Form Pluggable (SFP) transceivers
that support 1000BASE-X for interoperability with Gigabit fiber
equipment. SFP transceivers enable adaptability to different
fiber types, speed and distances, and support Coarse Wave
Division Multiplexing (CWDM) technology to increase the
bandwidth capacity of fiber infrastructure.
The GX/T also supports SC and ST fixed fiber connectors for
The GX/T also supports SC and ST fixed fiber connectors for
multimode, single-mode fiber; and single mode single-fiber
models are available.
The Plug-and-Play capability of the miConverter GX/T simplifies
The Plug-and-Play capability of the miConverter GX/T simplifies
fiber-to-the-laptop and fiber-to-the-desktop deployments.
Both the fiber port and the UTP port support auto-negotiation,
an IEEE standard which defines how all the communicating
devices automatically perform their configuration functions.
Auto-negotiation achieves the best possible mode of
operation (speed, duplex mode and Pause mode) between
the devices.
The auto-negotiation feature can be disabled on both ports
The auto-negotiation feature can be disabled on both ports
(for manual configuration) using DIP-switches on the module.
This is useful in a situation where the GX/T is connected to a
non-negotiating device and the configuration parameters must
be set manually.
Network flow control is managed by the Pause function
Network flow control is managed by the Pause function
(configured via auto-negotiation or manually) that prevents
network congestion on both the UTP and fiber ports. When
Pause is enabled and the device is experiencing network
congestion, it will send out a Pause signal to its link partner,
instructing it to slow down data transmission.
The GX/T generates a remote fault indication when it detects
The GX/T generates a remote fault indication when it detects
link fault conditions, and reports detection of these signals
by displaying status on the LED. Through user DIP-switch
configuration, the detection of these indicators or link modes
can also be propagated to the other port on the GX/T as a
means of notifying connected end-devices of the link fault.
Diagnostic data is provided through LED indicators that assist
Diagnostic data is provided through LED indicators that assist
in network installation and maintenance. The LEDs report the
availability of power, port activity and link status and speed.
The miConverter GX/T combines Gigabit Ethernet connectivity
The miConverter GX/T combines Gigabit Ethernet connectivity
with the lightweight design and low-power consumption required
for both permanent deployment and mobile service networks.
SFPs not included. Shown with optional wall mount bracket
KEY FEATURES