Philips 3D Ultra-Slim LED TV 40PFL4308T 40PFL4308T/12 ユーザーズマニュアル
製品コード
40PFL4308T/12
EN 32
Step 3: Copy channels to a TV with no
channels installed
1. Switch on the second TV, on which you
want to copy the channel list.
Initial installation starts.
2. Follow the onscreen instructions and
select the same country as the TV whose
channel list you want to copy.
3. Skip the search for channels.
4. Connect the USB storage device.
5. Press .
channels installed
1. Switch on the second TV, on which you
want to copy the channel list.
Initial installation starts.
2. Follow the onscreen instructions and
select the same country as the TV whose
channel list you want to copy.
3. Skip the search for channels.
4. Connect the USB storage device.
5. Press .
6. Select [Setup] > [Channel settings] or
[Satellite settings].
7. Select [Channel installation] > [Copy
channel list] > [Copy to TV], then press
OK.
The channel list is copied to the TV storage
device.
8. Disconnect the USB storage device.
[Satellite settings].
7. Select [Channel installation] > [Copy
channel list] > [Copy to TV], then press
OK.
The channel list is copied to the TV storage
device.
8. Disconnect the USB storage device.
Step 3: Copy channels to a TV with
pre-installed channels
1. Switch on the second TV, on which you
want to copy the channel list.
2. Press .
pre-installed channels
1. Switch on the second TV, on which you
want to copy the channel list.
2. Press .
3. Select [Setup] > [Search for channels] >
[Reinstall channels], then press OK.
The country menu is displayed.
4. Make sure that the country setting is the
same as for the first TV.
5. Press
[Reinstall channels], then press OK.
The country menu is displayed.
4. Make sure that the country setting is the
same as for the first TV.
5. Press
.
6. Press [Cancel] to exit.
7. If the country setting is different, reinstall
the second TV to match the country setting
7. If the country setting is different, reinstall
the second TV to match the country setting
of the first TV. See Change your TV settings
> Reset all (Page 36).
8. Connect the USB storage device to the
second TV.
9. Press .
> Reset all (Page 36).
8. Connect the USB storage device to the
second TV.
9. Press .
10. Select [Setup] > [Channel settings] or
[Satellite settings].
11. Select [Channel installation] > [Copy
channel list] > [Copy to TV], then press
OK.
The channel list is copied to the second TV.
12. Disconnect the USB storage device.
[Satellite settings].
11. Select [Channel installation] > [Copy
channel list] > [Copy to TV], then press
OK.
The channel list is copied to the second TV.
12. Disconnect the USB storage device.
Satellite settings
What you can do
This TV can receive signals from 4 different
low noise block-down converters (LNBs).
An LNB is mounted at the end pole of the
dish antenna and captures signals from a
satellite.
Note:
low noise block-down converters (LNBs).
An LNB is mounted at the end pole of the
dish antenna and captures signals from a
satellite.
Note:
Satellite reception is available for certain
models only. [Search for satellite] is
only available if the TV supports DVB-S.
only available if the TV supports DVB-S.
To receive satellite channels, connect a
satellite receiver to the SAT connector
on your TV.
satellite receiver to the SAT connector
on your TV.
Install satellite channels
Reinstall satellites
1. While you watch TV, press .
1. While you watch TV, press .
2. Select [Setup] > [Search for satellite] >
[Reinstall satellites].
3. Follow the onscreen instructions to
complete the installation.
[Reinstall satellites].
3. Follow the onscreen instructions to
complete the installation.
4. Once complete, select [Finish], then press
OK.
OK.
Select connection type
When you install satellite channels, you need
to set the connection type. The number of
LNBs on your dish antenna determines the
number of satellite channels you can install.
1. While you reinstall satellites, select
When you install satellite channels, you need
to set the connection type. The number of
LNBs on your dish antenna determines the
number of satellite channels you can install.
1. While you reinstall satellites, select
[Settings], then press OK.
2. Select [Connection type].
3. Select a setting, then press OK.
2. Select [Connection type].
3. Select a setting, then press OK.
[1 satellite (Single LNB)]: Select if you
have only one LNB.
have only one LNB.
[2 satellites (DiSEqC Mini)]: Select if
you have 2 LNBs.
you have 2 LNBs.
[3 or 4 satellites (DiSEqC 1.0)]: Select
for 3 or 4 LNBs.
for 3 or 4 LNBs.
[Unicable for 1 satellite]: Select if you
have a Unicable setup with 1 satellite.
have a Unicable setup with 1 satellite.
[Unicable for 2 satellites]: Select if you
have a Unicable setup with 2 satellite.
have a Unicable setup with 2 satellite.