Midland BTX1 C1033.01 データシート

14  - Midland BTX1 

 

› Intercom driver - passanger (10mt).  

 

› Connect your phone to receive and place phone call and listen to stereo music

 

› Connect your GPS for voice street indication

 

› Connection for PMR466 radio with internal or external Bluetooth

 

› AUX wired connection for MP3 player and PMR446 radio

 

› Setup and Firmware update via USB connection to a PC

 

› Single BTX1 Intercom kit with one unit only

 

› Twin BTX1 Intercom kit with with two units 
Depending on the model purchased, the package contains the following 
parts:

 

› 1 BTX1 communication unit

 

› 1 audio kit with two stereo speakers, microphone with boom and wired mi-

crophone

 

› 1 plate with bi-adhesive strip to fix the unit onto the helmet

 

› 1 clamp to fix the unit onto the helmet

 

› 1 miniUSB wall-mounting power supply
BTX1 Twin

 

› 2 BTX1 communication units

 

› 2 audio kits with two stereo speakers, microphone with boom and wired mi-

crophone

 

› 2 plates with bi-adhesive strip to fix the unit onto the helmet

 

› 2 clamps to fix the unit onto the helmet

 

› 1 miniUSB wall-mounting power supply with double plug
The units included in the TWIN kit are already paired and can therefore be immedia-
tely used in Intercom mode.

› Bluetooth ver. 3.0 stereo (Headset/Handsfree/A2DP protocol)

 

› AGC system automatically controls the volume in relation to background noise

 

› Voice (VOX) or manual communications activation

 

› Manual controls to enable: telephone, intercom and wire connection 

 

› Fully waterproof

 

› Lithium battery with 10 hours talk time

 

› Recharge time: app. 6 hours
Bluetooth connections:
With identical device for Driver to Passanger intercom
Bluetooth devices:

 

› Mobile phone with MP3 player Stereo (A2DP protocol), GPS (Garmin Zumo and 

TomTom Rider 1 and 2)

 

› PMR446 transceivers (with built-in or external Bluetooth connection) for 

group bike-to-bike communications 

 

› For stereo audio input like iPod/MP3 player (with optional cable)

 

› For PMR446 transceivers (with optional cable)
Attention: Midland BTX1 is designed to withstand rain and water. However, if it is 
raining, always verify that the rubber caps protecting the sockets are fully fitted.

Attention: Make sure that the unit is fully charged before use. Allow at least 8 hours 
for a full charge before using the unit for the first time. 
Charge the unit by inserting the wall-charger into the charging socket (lift the 
rubber cover to insert the plug).
The red LED on the unit will start flashing when charging begins.
Allow the headset to charge until the unit stops flashing or the blue LED turns on.
When the charge is complete (the red LED is not flashing), release the headset 
from the charger.

Normally, after the first time, it takes 6 hours for a full charge.
Attention: every time the mini USB recharging plug is inserted (or detached), the 
device is automatically turned off. To use it while it is in charge, you should turn the 
device on with the plug already inserted.

The BTX1 has five buttons on the front; the main three big button are multi fun-
ctions buttons: the Forward (on the left), the middle button and the Rear (on the 
right), the two small rounded buttons are the Volume + and Volume -.

On the bottom of the unit you can find three wired connection:
Charger jack: enables to recharge the unit using a standard miniUSB power 
supply
Audio kit jack: enable to connect an audio kit (stereo headset and microphone)
Auxiliary audio jack (AUX) 2.5mm: can be used to connect an audio source, like 
a stereo iPod/MP3 player or PMR446 transceiver

The audio system includes two ultra-flat 
stereo speakers and two interchangeable 
microphones, which are both supplied with 
a bracket and wired connection.

Fixing the stereo speakers
The two stereo speakers have a Velcro/adhesive strip that aids their fixing into 
your helmet.
Beware not to  completely cover your ear with the speakers, you must always be 
able to listen to the traffic sound and your indicators.
The microphone can be fixed onto the helmet in two ways:
Boom Microphone
Place the section with the Velcro/adhesive strip between the padding and the 
rigid cover of the helmet, so that the microphone is correctly positioned in front of 
your mouth and that the white symbol is facing your mouth. This type of micro-
phone is suited for Open Faced and Flip Front helmets.

Wired microphone
Using the Velcro/adhesive strip, place the microphone inside the helmet in front 
of your mouth. This type of microphone is more suited for Full Faced helmets. The 
mini connector on the microphone allows you choose the microphone that best 
suits the helmet you are using.

Audio kit jack
The audio kit must then be connected to the central jack of the Midland BTX1 unit 
using the “L” shaped connector.