Mitsubishi Electronics Mitsubishi Digital Electronics Video Gaming Accessories FX3G ユーザーズマニュアル
145
FX
3G
/FX
3U
/FX
3UC
Series Programmable Controllers
Programming Manual - Basic & Applied Instruction Edition
4 Devices in Detail
4.12 Pointer [P and I]
1
In
trodu
ct
ct
ion
2
O
ver
vi
ew
3
In
st
ru
ct
ion
Li
st
4
D
evices
in D
etail
etail
5
Specifi
ed t
he
he
D
evice &
C
onst
ant
ant
6
Bef
ore
ore
Pr
ogr
am
am
m
ing
7
B
asic
In
st
ru
ct
ion
8
FNC0
0-F
0-F
NC0
9
Pr
ogr
am
Flow
am
Flow
9
FN
C
C
10-FN
C
19
Mo
ve
ve
&
Co
mp
are
are
10
FNC2
0-F
0-F
NC2
9
Ar
ith.
&
&
Logic
O
per
ati
ati
on
4.12.3 Functions and operation examples of pointers for interrupt
→ For details on interrupt function, refer to Chapter 36.
There are three types of pointers for interrupt. When in use, they are combined with IRET(FNC03), EI(FNC04) and
DI(FNC05) for interrupt return, enabling interrupt and disabling interrupt.
DI(FNC05) for interrupt return, enabling interrupt and disabling interrupt.
1. Pointers for input interrupt (delay interrupt): 6 points
→ For details on input interrupt function, refer to Section 36.3 and Section 36.4.
The PLC can receive input signals from specific input numbers without influence of the operation cycle of the PLC. By
using these input signals as triggers, the PLC executes interrupt routine programs.
Because pointers for input interrupt can handle signals shorter than the operation cycle, use them for high priority
processing during sequence control and for control handling short pulses.
using these input signals as triggers, the PLC executes interrupt routine programs.
Because pointers for input interrupt can handle signals shorter than the operation cycle, use them for high priority
processing during sequence control and for control handling short pulses.
*1.
Cleared when the PLC mode switches from RUN to STOP.
Non-overlap of input numbers
Inputs X000 to X007 are used for high speed counters, input interrupt, pulse catch, SPD/ZRN/DSZR/DVIT instructions
and general-purpose inputs. When assigning functions, there should be no overlap between those input terminals.
For example, when the input interrupt pointer I001 is used, X000 is occupied. As a result, "C235, C241, C244, C246,
C247, C249, C251, C252 and C254", "input interrupt pointer I000", "pulse catch contact M8170" and "SPD instruction
using X000" cannot be used.
Delay function of input interrupt
and general-purpose inputs. When assigning functions, there should be no overlap between those input terminals.
For example, when the input interrupt pointer I001 is used, X000 is occupied. As a result, "C235, C241, C244, C246,
C247, C249, C251, C252 and C254", "input interrupt pointer I000", "pulse catch contact M8170" and "SPD instruction
using X000" cannot be used.
Delay function of input interrupt
This input interrupt has a function to delay the execution of interrupt routine in units of 1ms.
The delay time is specified by the following pattern program.
This delay function can electrically adjust the mounting position of sensors for input interrupts without shifting the
actual position.
The delay time is specified by the following pattern program.
This delay function can electrically adjust the mounting position of sensors for input interrupts without shifting the
actual position.
*2.
This function is supported only in FX
3U
/FX
3UC
PLCs.
Input
Pointer for input interrupt
Interrupt disabling flag
ON duration or OFF duration of input
signal
Interrupt at rising
edge
Interrupt at falling
edge
FX
3U
/FX
3UC
FX
3G
X000
I001
I000
M8050
*1
5
µs or more
10
µs or more
X001
I101
I100
M8051
*1
X002
I201
I200
M8052
*1
50
µs or more
X003
I301
I300
M8053
*1
10
µs or more
X004
I401
I400
M8054
*1
X005
I501
I500
M8055
*1
50
µs or more
M8393
FNC 12
MOV
K{{{*
Delay time specifying program
Make sure to describe the delay time specifying
program shown on the left at the head of an
interrupt routine program.
Because this is a pattern program, change only
the delay time [1].
Only a constant (K) or data register (D) can be
used to specify the delay time*.
I
D8393
[1] Delay time (unit: ms)
FNC 03
IRET
Program to be processed by input interrupt
Contact for setting delay time
•
Interrupt program is finished
•