Marantz 5411 10470 007M ユーザーズマニュアル
44
ENGLISH
Remote control
Operating range of the remote control
Point the remote control at the remote sensor when operating it.
30°
30°
Approx. 23 ft /7 m
NOTE
The set may function improperly or the remote control may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
Inserting the batteries
q
Slide the rear lid in the
direction of the arrow and
remove it.
remove it.
w
Load the two batteries
properly as indicated by
the marks in the battery
compartment.
the marks in the battery
compartment.
R03/AAA
e
Put the rear cover back on.
If the battery level is low, the remote control signal transmission/
status display flashes 5 times when a button is pressed.
In this case, replace the batteries soon.
• If the batteries are completely exhausted, the remote control signal
status display flashes 5 times when a button is pressed.
In this case, replace the batteries soon.
• If the batteries are completely exhausted, the remote control signal
transmission/status indicator goes dark.
NOTE
• Insert the specified batteries in the remote control.
• Replace the batteries with new ones if the set does not operate
• Replace the batteries with new ones if the set does not operate
even when the remote control is operated close to the unit. (The
supplied batteries are only for verifying operation.)
supplied batteries are only for verifying operation.)
• When inserting the batteries, be sure to do so in the proper direction,
following the q and w marks in the battery compartment.
• To prevent damage or leakage of battery fluid:
• Do not use a new battery together with an old one.
• Do not use two different types of batteries.
• Do not attempt to charge dry batteries.
• Do not short-circuit, disassemble, heat or dispose of batteries in
• Do not use two different types of batteries.
• Do not attempt to charge dry batteries.
• Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
• Do not keep the battery in a place exposed to direct sunlight or in
places with extremely high temperatures, such as near a heater.
• If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
• Remove the batteries from the remote control if it will not be in use
for long periods.
• Used batteries should be disposed of in accordance with the local
regulations regarding battery disposal.
Remote control settings (remote control side)
Switches when this unit remote control operates another
MARANTZ BD players in the vicinity.
MARANTZ BD players in the vicinity.
Set the remote control code simultaneously on the unit, too
(vpage 37 “Remote ID”).
(vpage 37 “Remote ID”).
G
Remote control code settingH
• The supplied remote control has two remote control code settings:
BD 1 and BD 2.
• The code is set to “BD 1” at the factory.
• To set the code to “BD 2”, hold the 2 and the Number button (
• To set the code to “BD 2”, hold the 2 and the Number button (
2
)
pressed for more than five seconds.
• To set (return) the code to “BD 1”, hold the 2 and the Number
button (
1
) pressed for more than five seconds.
If the signal code of the remote control does not match the signal
code of the unit, the remote control code set on the unit is shown on
the display.
G
ExampleH
If the code setting on the unit is “BD1”, and the setting on the remote
control is “BD2”, “BD1” is shown on the display.
control is “BD2”, “BD1” is shown on the display.
NOTE
• Match the signal code of the remote control with the signal code of
the unit. If the remote control code is different, you cannot operate
the this unit with the remote control.
the this unit with the remote control.
1.UD5005U_ENG_0930.indd 44
2010/10/04 18:00:37