Marantz SR5300 ユーザーズマニュアル
5
ENGLISH
R E A R P A N E L C O N N E C -
TIONS (SEE PAGE iii.)
TIONS (SEE PAGE iii.)
All connections to the rear panel should be made with the entire
system powered off.
To avoid errors, it is advisable to connect one cable at a time between
the various components.
system powered off.
To avoid errors, it is advisable to connect one cable at a time between
the various components.
a FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial cable, or a cable
network FM source.
network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the terminals marked
“AM” and “GND”.
The supplied AM loop antenna will provide good AM reception in most
areas.
Position the loop antenna until you hear the best reception.
“AM” and “GND”.
The supplied AM loop antenna will provide good AM reception in most
areas.
Position the loop antenna until you hear the best reception.
s PRE OUT jacks
Jacks for Front - L/R, Center,Surround and Surround center.
Use these jacks for connection to an external power amplifier.
Use these jacks for connection to an external power amplifier.
d SUB WOOFER output jack
Connect to the input jack(s) of the power amplifier for subwoofer
channel or powered subwoofer.
channel or powered subwoofer.
f Analog AUDIO outputs for audio
recording equipment
TAPE and CD-R/MD
Connect each output to the audio inputs (REC in) of your recording
equipment.
Connect each output to the audio inputs (REC in) of your recording
equipment.
g Analog AUDIO inputs
CD, TAPE, and CD-R/MD
Connect the audio outputs of your source components to the input
jacks on the receiver.
Connect the audio outputs of your source components to the input
jacks on the receiver.
h VIDEO (VIDEO/S-VIDEO) outputs
VCR1, and DSS/VCR2
Connect each output to the video input (REC in) of your video
recording equipment.
Connect each output to the video input (REC in) of your video
recording equipment.
j TV MONI. (VIDEO/S-VIDEO) output jacks
Connect the TV MONI jack to your TV’s video input (VIDEO IN) jack.
You can connect your video equipment with S-VIDEO jacks if
possible, or the composite VIDEO jacks.
You must use the same type of connection from your video player into
the receiver, and out of the receiver into your TV.
Both must be composite video or both must be S-Video. You cannot
convert a signal from one type to the other.
You can connect your video equipment with S-VIDEO jacks if
possible, or the composite VIDEO jacks.
You must use the same type of connection from your video player into
the receiver, and out of the receiver into your TV.
Both must be composite video or both must be S-Video. You cannot
convert a signal from one type to the other.
k SPEAKER SYSTEMS terminals
FRONT Left & Right speakers output terminals
Connect to the front left & right speakers.
CENTER speaker output terminals
Connect to the center speaker.
SURROUND Left & Right speakers output terminals
Connect to the surround (rear) left & right speakers.
SURROUND Center speaker output terminals
Connect to the surround center speaker.
Connect to the front left & right speakers.
CENTER speaker output terminals
Connect to the center speaker.
SURROUND Left & Right speakers output terminals
Connect to the surround (rear) left & right speakers.
SURROUND Center speaker output terminals
Connect to the surround center speaker.
l 6.1 CH INPUT jacks
Connect to the outputs of DVD Audio player, SACD Multi channel
player or an external multichannel decoder.
player or an external multichannel decoder.
¡0 DIGITAL outputs
Optical and Coaxial
Connect to the digital input of your digital recording equipment.
Connect to the digital input of your digital recording equipment.
¡1 DIGITAL inputs
Dig.1,2 (Optical) and Dig. 3, 4 (Coaxial)
Connect each input to the digital output of your source equipment.
Use the SETUP MAIN MENU to assign digital input to appropriate
source. (see page. 16)
Connect each input to the digital output of your source equipment.
Use the SETUP MAIN MENU to assign digital input to appropriate
source. (see page. 16)
Note :
• The coaxial connections are not for AC-3 RF from the LD
player, If you want to decode this type of signal, an external
demodulator must be used.
demodulator must be used.
¡2 REMOTE CONTOROL IN/OUT terminals
Connect to a Marantz component equipped with remote control (RC-
5) terminals.
5) terminals.
¡3 Analog AUDIO outputs for video
recording equipment
VCR1, and DSS/VCR2
Connect each output to the audio inputs (REC in) of your video
recording equipment.
Connect each output to the audio inputs (REC in) of your video
recording equipment.
¡4 Analog AUDIO inputs for video source
equipment
TV, DVD, VCR1, and DSS/VCR2
Connect each input to the audio outputs of your video source
equipment.
Connect each input to the audio outputs of your video source
equipment.
¡5 VIDEO inputs
TV, DVD, VCR1, and DSS/VCR2
Connect each input to the video outputs of your video source
equipment.
Connect each input to the video outputs of your video source
equipment.
¡6 S-VIDEO inputs
TV,DVD, VCR1,and DSS/VCR2
Connect each input to the S-video outputs of your video source
equipment.
Connect each input to the S-video outputs of your video source
equipment.
¡7 AC OUTLET
Connect the power cables of components such as a DVD and CD
player to these outlets. Both SWITCHED and UNSWITCHED outlets
are provided.
The one marked SWITCHED provides power only when the SR5300
is turned on and is useful for components which you use every time
you play your system.
The one marked UNSWITCHED is always live as long as the SR5300
is plugged into a live outlet.
A component connected here may be left on permanently, or may be
switched off with its own power switch.
player to these outlets. Both SWITCHED and UNSWITCHED outlets
are provided.
The one marked SWITCHED provides power only when the SR5300
is turned on and is useful for components which you use every time
you play your system.
The one marked UNSWITCHED is always live as long as the SR5300
is plugged into a live outlet.
A component connected here may be left on permanently, or may be
switched off with its own power switch.
Caution:
• In order to avoid potential turn-off thumps, anything plugged in
here should be powered up BEFORE the SR5300 is turned on.
• The capacity of this AC outlet is 120W. Do not connect devices
that consume electricity more than the capacity to this AC
outlet. If total power consumption of connected devices
exceeds the capacity, protection circuit shuts down the power
supply.
outlet. If total power consumption of connected devices
exceeds the capacity, protection circuit shuts down the power
supply.
¡8 AC IN
Connect to AC power outlet.
SR5300 can be powered by 120V AC only.
SR5300 can be powered by 120V AC only.