Cooper Bussmann Power Module PS ユーザーズマニュアル
8-29-01
XXXXXX
Bussmann
®
Power Module
™
Switch
PS
All-In-One Module
Form No. PS
Page 1 of 5
BIF Doc# 1145
Bussmann
®
Power Module™ Switch
Standard Features:
• 30-400 amp 600 Vac 3p Fused Power Switch
• 200,000 amp RMS Short-Circuit Current Rating
• Shunt trip 120V
• Control power terminal block
• Ground lug per NEC
• Class J fuse mounting only
• 200,000 amp RMS Short-Circuit Current Rating
• Shunt trip 120V
• Control power terminal block
• Ground lug per NEC
• Class J fuse mounting only
1
Optional Features:
• Control power transformer with fuses and blocks
• Fire safety interface relay
• Key to test switch
• Pilot light – “ON”
• Isolated neutral lug
• Fire safety interface relay
• Key to test switch
• Pilot light – “ON”
• Isolated neutral lug
2
• Mechanically interlocked auxiliary contact for hydraulic
elevators with battery backup (5 amp 120 Vac rated)
• Fire Alarm Voltage Monitoring Relay (To monitor Shunt Trip
Voltage)
• NEMA 3R, 4, and 12 enclosures available
3
• Phase failure and undervoltage relay available, consult
factory
• For added protection, use the Bussmann SAMI fuse
covers to improve maintenance personnel protection
4
(OSHA 1910.333, paragraph C)
Agency Information:
U.L. 98 Enclosed and Dead Front Switch
Guide 96NK3917, File E182262
NEMA 1, U.L. 50, listed enclosure
cU.L. per Canadian Standards C22.2, No. 0-M91-CAN/CSA
cU.L. per Canadian Standards C22.2, No. 0-M91-CAN/CSA
C22.2, No. 4-M89 Enclosed Switch
Power Module™ Switch
Rating (Amps)
Power Module Switch Catalog No.
30
PS3
60
PS6
100
PS1
200
PS2
400
PS4
Optional Accessories
1
Catalog
Rating
Number
Option 1
Control Power Transformer
Control Power Transformer
208V
T20
(CPT) Std. 100VA with PRI &
240V
T24
SEC Fuse (120V Secondary)
480V
T48
600V
T60
Option 2
Fire Safety Interface
Fire Safety Interface
24 Vdc Coil
R2
Relay (3PDT, 10 amp, 120V)
120 Vac Coil
R1
Option 3
Key to Test Switch
Key to Test Switch
120V
K
Option 4
Pilot Light – “ON”
Pilot Light – “ON”
Red
R
Green
G
White
W
Option 5
Isolated Neutral Lug
Isolated Neutral Lug
30-60A
N6
(Full Capacity)
2
100A
N1
200A
N2
400A
N4
Option 6
Mechanically interlocked auxiliary contact
Mechanically interlocked auxiliary contact
1 NO & 1 NC
A
for hydraulic elevators with automatic
recall (5 amp 120 Vac rated)
recall (5 amp 120 Vac rated)
Option 7
Fire Alarm Voltage Monitoring Relay
Fire Alarm Voltage Monitoring Relay
Single-Pole
F1
(To monitor Shunt Trip Voltage)
Three-Pole
F3
Option 8
Optional Enclosure
Optional Enclosure
NEMA 3R
U
NEMA 4
Y
NEMA 12
Z
Catalog No. Construction: Catalog number of PS Switch
Options as required in option order as listed above
(i.e. option 1, 2, 3, etc.)
Options as required in option order as listed above
(i.e. option 1, 2, 3, etc.)
Example: • 100A S.T. Switch 480V-3P – PS1
• 480–120V CPT – T48
• 120 Vac Coil Fire Safety Interface Relay – R1
• Pilot Light - “ON” (Green) – G
• Mech. Interlock (1 NO & 1 NC) – A
• 120 Vac Coil Fire Safety Interface Relay – R1
• Pilot Light - “ON” (Green) – G
• Mech. Interlock (1 NO & 1 NC) – A
Catalog Number PS1T48R1GA
1
Class J fuses not included.
2
Oversized 200% rated neutral option available where required by excessive
non-linear loads.
non-linear loads.
3
Through 200A.
4
Through 100A.
5
Options 1,2,& 6 are standard for elevator circuits.
Bussmann
®
How to configure Part Numbers:
Step 1: Select Switch Amperage
1
Step 2: Select Options Needed
5