KitchenAid KRMF706EBS 使用とお手入れ

PERFORMANCE DATA SHEET

This system has been tested according to NSF/ANSI Standards 42, 53 and 401 for the reduction of the substances listed below. The concentration 
of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving 
the system, as specified in NSF/ANSI Standards 42, 53, and 401. 

 

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.75 gpm (2.84 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 
22°C). Rated service capacity = 200 gallons (757 liters).
The compounds certified under NSF 401 have been deemed as “emerging compounds/incidental contaminants.” Emerging compounds/incidental 
contaminants are those compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these 
compounds can affect the public acceptance/perception of drinking water quality. 

■

It is important that operational, maintenance, and filter replacement 
requirements be carried out for the product to perform as advertised. 
Property damage can occur if all instructions are not followed.

■

The disposable cartridge must be changed at least every 6 months.

 

■

Use replacement filter P9RFWB2L, part #EDR2RXD1/EDR2RXD1B. 
2015 suggested retail price of $49.99 U.S.A./$49.99 Canada. Prices 
are subject to change without notice.

■

The filter monitor system measures the amount of water that passes 
through the filter and alerts you when it is time to replace the filter. 
Refer to the “Using the Controls” or “Water Filtration System” section 
(in the User Instructions or User Guide) to learn how to check the 
water filter status.

 

■

After changing the water filter, flush the water system. See “Water 
and Ice Dispensers” or “Water Dispenser” in the User Instructions or 
User Guide.  

■

These contaminants are not necessarily in your water supply. While 
testing was performed under standard laboratory conditions, actual 
performance may vary. 

■

The product is for cold water use only.

■

The water system must be installed in compliance with state and 
local laws and regulations. 

■

Do not use with water that is microbiologically unsafe or of unknown 
quality without adequate disinfection before or after the system. 
Systems certified for cyst reduction may be used on disinfected 
waters that may contain filterable cysts.
EPA Est. No. 082047-TWN-001

■

Refer to the “Warranty” section (in the User Instructions or User 
Guide) for the Manufacturer’s limited warranty, name and telephone 
number. 

System tested and certified by NSF International against NSF/ANSI 
Standard 42, Standard 53, and Standard 401 for the reduction of 
contaminants specified on the Performance Data Sheet.  

Chlorine Taste/Odor

2.0 mg/L ± 10%

50% reduction

  97.0%

Particulate Class I

*

At least 10,000 particles/mL

85% reduction

>99.9%

Lead: @ pH 6.5 / @ pH 8.5

0.15 mg/L± 10%

0.010 mg/L

>99.3% / 98.6%

Benzene

0.015 mg/L ± 10%

0.005 mg/L

93.8%

p-Dichlorobenzene

0.225 mg/L ± 10%

0.075 mg/L

99.8%

Carbofuran

0.08 mg/L ± 10%

0.040 mg/L

81.9%

Toxaphene

0.015 ± 10%

0.003 mg/L

>95%

Atrazine

0.009 mg/L ± 10%

0.003 mg/L

87.0%

Asbestos

10

7 

to 10

8 

fibers/L

††

99%

>99%

Live Cysts

†

50,000/L min. 

99.95%

>99.99%

Turbidity

11 NTU ± 10% 

0.5 NTU

96.9%

Lindane

0.002 ± 10%

0.0002 mg/L

>99.2%

Tetrachloroethylene

0.015 mg/L ± 10%

0.005 mg/L

96.6%

O-Dichlorobenzene

1.8 mg/L ± 10%

0.60 mg/L

92.3%

Ethylbenzene

2.1 mg/L ± 10%

0.70 mg/L

86.9%

1,2,4-Trichlorobenzene

0.210 mg/L ± 10%

0.07 mg/L

>99.8%

2,4 - D

0.210 mg/L ± 10%

0.07 mg/L

88.5%

Styrene

2.0 mg/L ± 10%

0.1 mg/L

99.6%

Toluene

3.0 mg/L ± 10%

1.0 mg/L

93.5%

Endrin

0.006 mg/L ± 10%

0.002 mg/L

81.7%

Atenolol

200 ± 20%

30 ng/L

95.7%

Trimethoprim

140 ± 20%

20 ng/L

96.1%

Linuron

140 ± 20%

20 ng/L

96.3%

Estrone

140 ± 20%

20 ng/L

95.3%

Nonylphenol

1400 ± 20%

200 ng/L

95.5%

Water Supply
Water Pressure
Water Temperature
Service Flow Rate

City or Well
30 - 120 psi (207 - 827 kPa)
33° - 100°F (0.6° - 37.8°C)
0.75 gpm (2.84 L/min.) @ 60 psi

*

†

††

Class I particle size: >0.5 to <1 um
Based on the use of Cryptosporidium parvum oocysts
Fibers greater than 10 um in length

® NSF is a registered trademark of NSF International.