Harbor Freight Tools 96067 ユーザーズマニュアル
Page 14
SKU 96067
for technical questions, please call 1-800-444-3353.
HoRiZontaL.BoRinG.safetY.RULes
avoid.unintentional.starting...Make sure you are prepared to begin work before
turning on the Router/Shaper.
never.leave.the.Router/shaper.unattended.when.it.is.running...Turn off the
never.leave.the.Router/shaper.unattended.when.it.is.running...Turn off the
Router/Shaper before leaving the work area.
always.place.scrap.wood.behind.the.workpiece.to.prevent.damage.to.the.
always.place.scrap.wood.behind.the.workpiece.to.prevent.damage.to.the.
drill.bit.and.to.avoid.splintering.
Always firmly support and guide the wood before and during drilling.
Use.only.the.speeds.listed.in.the.speed.Chart.
Make.sure.the.bit.never.touches.the.table,.Rip.fence,.or.Miter.Gauge.
keep.your.body.away.from.the.drill.bit.when.it.is.exposed.and.rotating.
keep.all.safety.guards.in.place.and.in.proper.working.order.
Make.sure.the.workpiece.is.free.from.nails.and.any.other.foreign.object.
Always firmly support and guide the wood before and during drilling.
Use.only.the.speeds.listed.in.the.speed.Chart.
Make.sure.the.bit.never.touches.the.table,.Rip.fence,.or.Miter.Gauge.
keep.your.body.away.from.the.drill.bit.when.it.is.exposed.and.rotating.
keep.all.safety.guards.in.place.and.in.proper.working.order.
Make.sure.the.workpiece.is.free.from.nails.and.any.other.foreign.object.
which.could.break.or.otherwise.damage.the.drill.bit.
never.start.the.the.machine.under.a.load...Allow the machine to reach full
never.start.the.the.machine.under.a.load...Allow the machine to reach full
speed before feeding a drill bit into the workpiece.
disC.sandeR.safetY.RULes
always.stand.on.the.left.of.the.sanding.disc’s.center...Never stand on the
right side of center.
Keep hands and fingers away from the Sanding Disc and the nearest edge
Keep hands and fingers away from the Sanding Disc and the nearest edge
of.the.table.
Use.only.the.speeds.listed.in.the.speed.Chart.
Hold the workpiece firmly when feeding it into the Sanding Disc.
Use.only.enough.pressure.to.touch.the.workpiece.lightly.against.the.
Use.only.the.speeds.listed.in.the.speed.Chart.
Hold the workpiece firmly when feeding it into the Sanding Disc.
Use.only.enough.pressure.to.touch.the.workpiece.lightly.against.the.
sandpaper.on.the.disc.
Before.sanding,.turn.on.the.disc.sander.and.check.for.excessively.loose.
Before.sanding,.turn.on.the.disc.sander.and.check.for.excessively.loose.
sanding.disc.
allow.the.sanding.disc.to.spin.up.to.full.speed.before.feeding.a.workpiece.
allow.the.sanding.disc.to.spin.up.to.full.speed.before.feeding.a.workpiece.
into.it...Do not ever feed a workpiece past the center line of the disc. .When
turning off the Disc Sander, allow the Sanding Disc to slow down and stop on its
own. Do not press against the Sanding Disc to stop it.
1.
2.
3.
4.
5.
6.
7.
8.
9.
5.
6.
7.
8.
9.
10.
1.
2.
3.
4.
5.
4.
5.
6.
7.