APC BR500CI-AS マニュアル

目次

• Once per second

  1
• Low

  1
• 155 - 280

  1
• The Back-UPS will switch to battery power less often. Use with equipment that is not sensitive to...

  1
• Twice per second

  1
• Medium (factory default)

  1
• 160 -280

  1
• Default, use in normal conditions.

  1
• Three times per second

  1
• High

  1
• 165 - 270

  1
• The Back-UPS will switch to battery power during any small fluctuation in voltage. Use with equip...

  1
• Connect the Battery and Turn on the Unit

  1
• Status Indicators

  1
  • On

    1
  • Off

    1
  • On-line - Back-UPS is supplying conditioned utility power to the connected equipment

    1
  • On (Off during 4 beeps)

    1
  • 4 beeps repeated every 30 seconds

    1
  • On-Battery - Back-UPS is supplying battery power

    1
  • Flashing

    1
  • Rapid Beeping (every 1/2 second)

    1
  • Low Battery Warning - The Back-UPS has 1.5 minutes of remaining battery power

    1
  • Flashing

    1
  • Constant tone

    1
  • Bad Battery Detected - Battery needs to be charged, or is at end of life. (See Battery Replacement.)

    1
  • Off

    1
  • Short beep every 4 seconds

    1
  • Low Battery Shutdown - During On Battery operation the battery power was almost completely exhaus...

    1
  • Off

    1
  • Constant Tone

    1
  • On Battery Overload - Connected equipment requires more power than provided by the Back-UPS batte...

    1
  • On

    1
  • Constant Tone

    1
  • On Line Overload - The power drawn by the connected equipment exceeds the power capacity of the B...

    1
  • Flashing

    1
  • Chirp every 2 seconds

    1
  • Charger Warning -Back-UPS has experienced an internal problem, but continues to power the load. C...

    1
  • Off

    1
  • Constant Tone

    1
  • Charger Fault - Back-UPS has an internal problem, and is no longer powering the load. Contact APC...

    1
• Specifications

  2
  • Input

    2
  • Voltage

    2
  • 230 Vac nominal

    2
  • Frequency

    2
  • 45-65 Hz

    2
  • Brownout Transfer

    2
  • 160 ±8% VAC, typical

    2
  • Over-voltage Transfer

    2
  • 280 VAC, typical

    2
  • Output

    2
  • UPS Capacity (total)

    2
  • 500 VA / 300 W

    2
  • Voltage On Battery

    2
  • 230 Vac rms

    2
  • (step-approximated sine wave)

    2
  • Frequency - On Battery

    2
  • 50 Hz ±1 Hz, 60 Hz ±1 Hz

    2
  • Transfer Time

    2
  • 50 Hz: 6ms typical, 10ms maximum 60 Hz: 5ms typical, 8ms maximum

    2
  • Protection and Filter

    2
  • AC Surge Protection

    2
  • Full time, 273 joules

    2
  • AC Input

    2
  • Re-settable circuit breaker

    2
  • Battery

    2
  • Type

    2
  • Maintenance free

    2
  • Average Life

    2
  • 2 - 5 years depending on the number of discharge cycles and environmental temperature

    2
  • Typical Recharge Time

    2
  • 10 Hours

    2
  • Physical

    2
  • Net Weight

    2
  • 5.4 kg

    2
  • Dimensions (H x W x D)

    2
  • 18.55 cm (H) x 11.5 cm (W) x 21.3 cm (D)

    2
  • Operating Temperature

    2
  • 0 oC to 40 oC (32 oF to 104 oF)

    2
  • Storage Temperature

    2
  • -15 oC to 45 oC (5 oF to 113 oF)

    2
  • Operating Relative Humidity

    2
  • 0 to 95% non-condensing

    2
  • Operating Elevation

    2
  • 0 to 3000 m (0 to 10,000 ft)

    2
• Adjusting Transfer Voltage and Sensitivity Settings

  1
  • 1 . Ensure the Back-UPS is off. Plug it into utility power.

    1
  • 2 . Press and hold ON/OFF until the LED repeatedly flashes. The unit is now in Program Mode.

    1
  • 3 . Release the button. The LED will flash once, twice, or three times per second, indicating the...

    1
  • 4 . Press ON/OFF within two seconds to change the setting. Each time the button is pressed, the L...

    1
  • 5 . To exit Program Mode, release the button and wait for the LED to stop flashing.

    1
• Connect Equipment

  1
  • Kết nối Thiết bị

    3
  • Nối Ắc quy vào và Bật Bộ Lưu điện lên

    3
  • Điều chỉnh Điện áp Chuyển và Các Thiết lập Độ nhạy

    3
  • Các Chỉ thị Trạng thái

    3
  • Xử lý trục trặc

    4
  • Đặc điểm kỹ thuật

    4
  • Thay Ắc quy

    4
  • Bảo hành

    4
  • Bảo dưỡng

    4
  • 连接设备

    5
  • 连接电池并启动装置

    5
  • 调节转换电压和敏感度设置

    5
  • 状态指示灯

    5
  • 故障排除

    6
  • 规格

    6
  • 电池更换

    6
  • 保修服务

    6
  • 服务

    6
  • 連接設備

    7
  • 連接電池並開啟裝置

    7
  • 調整傳輸電壓和敏感度 設定

    7
  • 狀態指示燈

    7
  • 故障排除

    8
  • 規格

    8
  • 電池更換

    8
  • 保固

    8
  • 維修

    8