Cisco Systems VCO/4K マニュアル

目次

• Storage/Control I/O Module

  1
• Specifications

  1
• Description

  2
  • Front Panel Indicators and Ports Assignments

    2
    • Figure4-1 Storage/Control I/O Module Front Panel

      3
    • :

      4
  • Hard Disk Drive

    4
    • Figure4-2 Location of the Hard Disk Drive on the Storage/Control I/O Module

      5
    • Figure4-3 Location of Hard Disk Drive LED on the Combined Controller

      6
  • Midplane Connectors

    6
    • Figure4-4 Control Midplane

      7
  • Serial Ports 1 and 2

    7
    • Table4-1 Serial Ports 1 and 2 Pin and Signal Assignments

      7
    • Figure4-5 I/O Module to Master Console—Cable Wiring Diagram

      8
    • Figure4-6 I/O Module to Remote Maintenance Modem—Cable Wiring Diagram

      8
  • Serial Ports 3 and 4

    9
    • Table4-2 Serial Ports 3 and 4 Pin and Signal Assignments

      9
  • Ethernet Interface

    9
    • Table4-3 Ethernet Port Pin and Signal Assignments

      10
  • Printer Interface

    10
    • Figure4-7 I/O Module to System Printer—Cable Wiring Diagram

      10
  • SCSI Interface

    11
• Hardware Configuration

  11
  • SCSI Termination Configuration

    11
  • Serial Port Configuration

    11
    • Serial Ports 1 Through 4 and Jumper Settings

      11
    • Serial Ports 1 Through 4

      12
      • Table4-4 Jumper Positions for DCE and DTE Modem Connections

        12
      • Figure4-8 Jumper Locations on the Storage/Control I/O Module Card

        12
      • Figure4-9 Jumper Configuration for DCE/DTE, Serial Ports 1-4

        13
      • Figure4-10 Jumper 15 Configuration of Clock Lines, Serial Port 4

        13
• Removal and Replacement Information

  13
  • Figure4-11 Storage/Control I/O Module Location

    14
  • Removal Procedures

    15
    • Step 1 Remove the Combined Controller that is connected to the Storage/Control I/O Module to be s...

      15
    • Step 2 Use a 1/8-inch bladed screwdriver to loosen the captive mounting screws at the top and bot...

      15
    • Step 3 Grasp the screws at the top and bottom of the card and pull the card away from the midplane.

      15
    • Step 4 When the card is free of the connector, grasp the sides of the front panel and pull the ca...

      15
    • Step 5 Grasp the card on its bottom edge as it is removed from the card rack.

      15
    • Step 6 When you have removed the card from the slot, place it on an antistatic mat or in an antis...

      15
    • Step 1 If servicing an active Storage/Control I/O Module, switch the active side to standby. Refe...

      15
    • Step 2 When the transition to standby is complete, remove and replace the Storage/Control I/O Mod...

      15
  • Replacement Procedures

    16
    • Step 1 Place the replacement Storage/Control I/O Module on the antistatic mat or envelope.

      16
    • Step 2 Verify that the Combined Controller that is to be connected to the Storage/Control I/O Mod...

      16
    • Step 3 Verify that all the jumpers on the replacement card correspond with those on the removed S...

      16
    • Step 4 Grasp the replacement card by the sides of the front panel and align it with the top and b...

      16
    • Step 5 Push the card inward until it makes contact with the midplane.

      16
    • Step 6 Firmly push the card toward the midplane. The card fits tightly into the midplane connecto...

      16
    • Step 7 Use a 1/8-inch bladed screwdriver to tighten the mounting screws at the top and bottom of ...

      16
    • Step 8 Plug the Combined Controller into the backplane.

      16
    • Step 9 If installing in a nonredundant system, make sure the system is powered on.

      16
    • Step 10 If the hard disk drive does not contain the Generic software, install the software. Refer...

      16
• Troubleshooting

  16
  • LEDs Not Illuminated

    16
  • Troubleshooting Reference Materials

    17