Emerson Figure i マニュアル

目次

• 1.0 Product Description

  5
  • 1.1 Prop Fan Condensing Units

    5
    • 1.1.1 Base System 95°F (35°C) Ambient Models

      5
    • 1.1.2 105°F (41°C) Ambient Models

      5
    • 1.1.3 Quiet-Line Models

      5
  • 1.2 Optional Equipment

    5
    • 1.2.1 Coated Coil

      5
    • 1.2.2 Pre-Charged Refrigeration Line Sets

      5
    • 1.2.3 Refrigerant Line Sweat Adapter Kit

      5
    • 1.2.4 277V Step-Down Transformer

      5
• 2.0 Installation

  6
  • 2.1 Equipment Inspection

    6
  • 2.2 Location Considerations

    6
  • 2.3 Dimensional Data

    7
    • Figure 1 Dimensions, horizontal air discharge

      7
    • Table 1 Cabinet and floor planning data, horizontal air discharge

      7
    • Figure 2 Dimensions, top air discharge

      8
    • Table 2 Electrical and piping connections, top air discharge

      8
    • Figure 3 Dimensional data, 277V step-down transformer

      9
  • 2.4 Piping and Electrical Connections

    10
    • Figure 4 Piping and electrical connections, horizontal discharge

      10
    • Table 3 Electrical and piping connections, horizontal air discharge

      10
    • Figure 5 Piping and electrical connections, top air discharge

      11
    • Table 4 Piping and electrical connections, top air discharge

      11
    • Figure 6 General piping arrangement

      12
    • Figure 7 Electrical field connections, 1- to 5-ton units

      13
    • Figure 8 Electrical field connections, 8-ton units

      14
    • Figure 9 Single-phase, 1-3 ton model schematic, typical

      15
    • Figure 10 Three-phase, 3-5 ton model schematic, typical

      16
    • Figure 11 Three-phase, 8 ton model schematic, typical

      17
  • 2.5 Piping Considerations

    18
    • 2.5.1 Piping for Elevation Differences between PFH and Evaporator

      18
      • Figure 12 Refrigerant piping diagram

        19
      • Table 5 Pipe length and condenser elevation relative to evaporator

        19
      • Table 6 Equivalent lengths for various pipe fittings, ft (m)

        19
    • 2.5.2 Pre-Charged Line Sets

      20
      • Table 7 Refrigerant charge in Liebert pre-charged R-407C line sets

        20
    • 2.5.3 Field-Fabricated Line Sets

      20
      • Table 8 Liebert PFH unit charge levels and coupling size

        21
      • Table 9 Recommended line sizes, OD Cu

        21
    • 2.5.4 Installation of Piping to Units

      22
      • Table 10 Piping connection sizes and torque

        22
      • Table 11 Line charges - refrigerant per 100 ft. (30m) of Type L copper tube

        22
    • 2.5.5 R-407C PFH Installed as a Replacement Condensing Unit in an R-22 System

      22
      • Remove Existing Condensing Unit

        23
      • Filter Drier Selection and Installation

        23
      • Install the New Condensing Unit

        23
    • 2.5.6 General System Charge Requirements

      24
      • Table 12 Evaporator Charge Levels

        24
  • 2.6 Electrical Connections

    25
    • Table 13 Design refrigerant pressures

      25
    • Table 14 Application limits

      25
    • 2.6.1 Low-Voltage Control Wire Connections

      25
    • 2.6.2 Low-Voltage Control Wire Sizing

      25
      • Table 15 Recommended minimum wire size

        25
  • 2.7 Electrical Data

    26
    • Table 16 Electrical data—Standard sound and ambient models (95°F/35°C) 60Hz

      26
    • Table 17 Electrical data—High ambient models (105°F/41°C) 60Hz

      26
    • Table 18 Electrical data—Quiet-Line models (95°F/35°C) 60Hz

      27
    • Table 19 Electrical data—Standard sound and ambient models (95°F/35°C) 50Hz

      27
    • Table 20 Electrical data—High ambient models (105°F/41°C) 50Hz

      27
    • Table 21 Electrical data - Quiet-Line models (95°F/35°C) 50Hz

      28
  • 2.8 Checklist for Completed Installation

    28
• 3.0 Operation

  29
  • 3.1 Compressor

    29
  • 3.2 High Head Pressure

    29
  • 3.3 Liebert Lee-Temp Flood Back Head Pressure Control

    29
  • 3.4 Hot Gas Bypass

    30
    • 3.4.1 Operation

      30
    • 3.4.2 Adjustment

      30
      • Figure 13 Hot gas bypass diagram

        31
• 4.0 Maintenance

  32
  • 4.1 General

    32
  • 4.2 Compressor Failure

    32
    • 4.2.1 Electrical Failure—Burnout

      32
    • 4.2.2 Mechanical Failure

      32
  • 4.3 Compressor Replacement

    33
  • 4.4 Field Charge Verification

    34
    • Table 22 Field verification charge

      34
• 5.0 Troubleshooting

  35
  • Table 23 Troubleshooting

    35