Whirlpool W10562346B 사용자 설명서
10
Changing the Sensor Cycle
Settings to Increase Drying Time
If all your loads on all Sensor Cycles are consistently not as
dry as you would like, you may change the default
settings to increase the default dryness level.
Your sensor drying settings can be adjusted to adapt to
Your sensor drying settings can be adjusted to adapt to
different installations, environmental conditions or personal
preference. This change is retained and will affect all of your
Sensor Cycles, not just the current cycle/load. There are 3
drying settings, which are displayed using the Cycle Status
light (Wet, Damp, Cool Down LEDs)
1
Factory preset dryness level.
2
Slightly drier clothes, 15% more drying time.
3
Much drier clothes, 30% more drying time.
To change the drying settings (on some models):
NOTE: The settings cannot be changed while the dryer is
running or paused. The dryer must be in standby mode (the
power button is off) to adjust the default settings.
1. Before starting a cycle, press and hold the TEMP button
for 6 seconds.
2. Press the TEMP button to select the dryness level
shown in the cycle status light display: Wet light on
= level 1, Wet and Damp lights on = level 2, and Wet,
Damp and Cool Down lights on = level 3.
3. Press START/PAUSE to save the new dryness level
setting.
Vacation, storage, and moving care
Install and store your dryer where it will not freeze. Because
some water may stay in the hoses, freezing can damage
your dryer. If storing or moving your dryer during freezing
weather, winterize it.
Non-Use or Storage Care
Operate your dryer only when you are at home. If you will
be on vacation or not using your dryer for an extended
period of time, you should:
1. Unplug dryer or disconnect power.
2. Clean lint screen. See “Cleaning the Lint Screen.”
1. Unplug dryer or disconnect power.
2. Clean lint screen. See “Cleaning the Lint Screen.”
Moving Care
For power supply cord-connected dryers:
1. Unplug the power supply cord.
2. Steam models only: Shut off water faucet.
3. Steam models only: Disconnect the water inlet hose
2. Steam models only: Shut off water faucet.
3. Steam models only: Disconnect the water inlet hose
from faucet, then drain the hose. Remove the hose from
the back of the dryer. Transport hose separately.
4. Make sure leveling legs are secure in dryer base.
5. Use tape to secure dryer door.
5. Use tape to secure dryer door.
For direct-wired dryers:
1. Disconnect power.
2. Disconnect wiring.
3. Steam models only: Shut off water faucet.
4. Steam models only: Disconnect the water inlet
2. Disconnect wiring.
3. Steam models only: Shut off water faucet.
4. Steam models only: Disconnect the water inlet
hose from faucet, then drain the hose. Transport
hose separately.
5. Make sure leveling legs are secure in dryer base.
6. Use tape to secure dryer door.
6. Use tape to secure dryer door.
Reinstalling the Dryer
Follow the “Installation Instructions” to locate, level,
and connect the dryer.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
Changing the drum light
(on some models)
1. Unplug dryer or disconnect power.
2. Open the dryer door. Locate the light bulb cover on
2. Open the dryer door. Locate the light bulb cover on
the back wall of the dryer. Using a Phillips-head screw
driver, remove the screw located in the lower right-hand
corner of the cover. Remove the cover.
3. Turn bulb counterclockwise. Replace the bulb with
a 10-watt appliance bulb only. Replace the cover and
secure with the screw.
4. Plug in dryer or reconnect power.