Hitachi hdc-401ex 사용자 설명서

90

89

Problem

Cause

Action

The camera
doesn

,

t turn on.

●

The batteries are not set correctly.

→Set the batteries correctly             .

●

Battery power is exhausted.

→Replace the batteries with new ones              .

●

Malfunction of the internal system, 

etc.

→Remove/disconnect the batteries/AC  

adapter and wait five seconds or more, 
set/connect the batteries/AC adapter 
correctly and then press the power button. 

●

The AC adapter (sold separately) is 

not connected correctly.

→Connect the AC adapter (sold separately) 

correctly             .

The batteries
run out quickly.

●

The camera is used in extremely cold 

temperatures.

―

●

Images are captured at high resolutions

or the flash is usedfrequently.

―

The camera turns
off suddenly.

●

The Power Off Time function was activated. →Turn on the power again.

●

Battery power is exhausted.

→Replace the batteries with new ones              .

The remaining
battery power is
not displayed
correctly.

●

The camera is used in extremely high or

low temperatures.

―

●

Battery power is exhausted.

→Replace the batteries with new ones              .

●

The flash is being charged (immediately

after switching to the flash mode).

→Wait until the flash is fully charged.

Problem

Cause

Action

Problem

Cause

Action

The LCD monitor
doesn

,

t show the

subjects.

●

The camera is in Playback mode.

→Press the MODE button to switch to Still 

Image Capture mode             .

●

The LCD monitor display is set to the 

Display Off mode.

→Press the display       button (

【

P】

) to 

switch the LCD monitor display mode

.

Image/video
cannot be
captured.

The flash
doesn

,

t work.

The flash was used
but the captured
image is still dark.

Captured
images are
blurred.

●

The shutter button was pressed while

another image was being recorded.

→Wait until the recording of the current image 

finishes before capturing a new image.

●

The shutter button was pressed while 

the flash was charging.

→Wait until the viewfinder lamp stops 

blinking before capturing an image.

●

Still images were taken while the camera was 
in Playback mode or Video Capture mode. 

→Press the MODE button to switch to Still 

Image Capture mode              .

●

Videos were taken when the camera was in 
Still Image Capture mode or Playback mode. 

→In the Still Image Capture mode, press the

MENU button and then select Video 
Capture mode               .

●

The Power Off Time function was activated 
and the camera was turned off.

→Turn on the power again.

●

The available memory space is low.

→Reduce the image size. 
→Delete images from the internal memory or

the memory card              , or swap the 
memory card with another              .

●

The write-protect switch on the memory card

is locked (the message Card Locked! is shown
on the LCD monitor).

→Unlock the write-protect switch on the 

memory card              .

●

The flash mode is set to        (Suppressed 
Flash (default setting)).

→Set the flash mode to      (Auto),       (Red-

Eye Reduction (Auto)),      (Night Scene), 
or        (Forced Flash)              .

●

The camera is in Close-Up       mode.

→Switch to Standard       mode and then select

the flash mode again               .

●

The subjects are too bright.

→Switch to the forced flash mode               .

●

The subjects are too far away.

→Bring the subjects within the effective flash-

interlocked range 
(approximately 1.1 to 2.1m)              .

●

The user

,

s fingers are covering the lens.

→Hold the camera correctly without the fingers

covering the lens.

●

Distant scenes are captured in Close-Up 
mode.

→Switch to Standard        mode (approximately 

110 cm or longer)               .

●

The subjects are too close.

→Bring the subjects within the image capture range 

(approximately 55 to 110 cm in Close-Up mode, or 
approximately 110 cm or more in Standard mode)

Troubleshooting

Appendix