Holmes HASF1522RCI 사용자 설명서

OPERATING INSTRUCTIONS:

Step 1.  Set fan base on a dry, level surface.
Step 2.  Plug cord into any standard 120 volt AC outlet. Please make sure

the Speed Control Knob is in the Off position. This knob is located

on the top of the Fan Motor Housing.

Step 3.  The speed is adjusted by turning the control knob to the desired

setting, Off-High-Med-Low.

Step 4.  The Oscillation Control Bar is located on the top of the Fan Motor

Housing. To Start Oscillation, Push Bar Down. To Stop Oscillation,

Pull Bar Up.

Special Note:  This fan can be used in a “straight-up”(Total-Flex)  position,

as a whole room air circulator (See Adjustment Instructions).

ADJUSTMENT INSTRUCTIONS:

This fan is equipped with two poles which allow you to adjust the height of

the fan for three height settings.

• Small Pole Only 30”

• Larger Pole Only 35”

• Both Poles for 50”

This fan is equipped with a multi-angle fan head which includes Total-

Flex™ for Whole-Room air circulation. Follow the steps below to properly

adjust the Tilt angle of your fan. Note: The Oscillation feature may be used

in all positions, including Total Flex.

Step 1.  To change the tilting angle of the fan head, simply loosen the Tilt

Adjustment Knob (see figure # 3) 

Step 2.  Move the fan head to the desired angle, and firmly tighten the

knob to lock in place.

Step 3.  This fan can be tilted to a straight-up position, offering Total-Flex

™

Oscillation.

Note: Whenever tilting the fan head, be sure to securely tighten in place.

CLEANING/MAINTENANCE INSTRUCTIONS:

Follow these instructions to correctly and safely care for your Holmes

Products stand fan. Please remember:

• Always unplug the fan before cleaning or disassembling. 

• Do not allow water to drip or enter the fan housing.

• Be sure to use a soft cloth moistened with mild soap solution.

• Do not use any of the following as a cleaner: gasoline, thinner, benzine.

(See instructions for fan head assembly on page 2, figure #3)
STEP 1: To access the fan blade, remove the front grill and blade cap.
STEP 2: Clean the fan blade,  front and rear grills with a soft, moist cloth.
STEP 3: Replace blade, tighten blade cap, and securely fasten the front grill.

Using a soft, moist cloth, with or without a mild, soap solution, carefully

clean the fan base, pole, and head. Please use caution around the motor

housing area. Do not allow the motor or other electrical components to be

exposed to water.

FAN STORAGE:

Your fan can be stored in the off-season either partially disassembled or

assembled. It is important to keep it in a safe, dry location. 

• If stored disassembled, we recommend using the original (or appropri-

ately sized) box.

• If stored assembled or partially assembled, remember to protect the

fan head from dust. 

The exclusive Holmes Products FanBonnet is available to protect your fan.

(See attached mail order form for special offer or call 1-800-5-HOLMES)

FAN SERVICE INSTRUCTIONS:

1. Do NOT attempt to repair or adjust any electrical or mechanical func-

tions on this unit. Doing so will void the warranty.
2. If you have any questions regarding this unit’s operation or believe any

repair is necessary, please call 1-800-5 HOLMES to speak with a Customer

Service Representative.
3. If you need to exchange the unit, please return it in its original carton,

with a sales receipt, to the store where you purchased it. If you are return-

ing the unit more than 30 days after the date of purchase, please see the

enclosed warranty.
4. If you have any other questions or comments, feel free to write us at:

ASSEMBLY INSTRUCTIONS:

Carefully unpack contents of carton.

You will need the base cover, weighted insert, 1 pole (either can be used,

they are interchangeable) and base nut.
STEP 1.  Insert 1 pole through the base cover and twist pole clockwise to

lock in position.

Be careful to

align the

cutaway /

grooves on the

threaded joint

(male end),

(see figure # 1)

with the two

protruding

raised pieces

inside the hol-

low end of the

base cover,

(see figure #1).

STEP 2.  Now turn the base cover upside down (pole facing floor) and

place the weighted insert into the base cover. The pole threads will

be exposed as they protrude through the base insert.

Note: Hold the pole, base cover and weighted insert in one hand while

tightening the base nut with the other hand.

STEP 3.  Now, place the base nut on the threaded section and hand tighten

base nut to securely fasten the pole to the base. 

Note: Do not use a tool to tighten the base nut.

You will need the second pole. 
Note: The poles are interchangeable.
Insert the pole with the threaded

joint (male end), (see figure # 2)

into the hollow end of the second

pole (female end), (see figure # 2)

until both poles meet. Be careful to

align the cutaway / grooves on the

threaded joint (male end) with the

two protruding pieces inside the hol-

low end of the second pole (female

end).
Now, slowly turn the pole with the

threaded joint clockwise to lock it

securely in place (see figure #2).

You are now ready to assemble the fan head (See Figure #3)
STEP 1.  Position the rear grill over the motor shaft, making certain the 2

notches at the top and bottom of the rear grill fit over the 2

prongs on the motor housing. Please make sure the rear grill fits

securely against the motor housing.

STEP 2.  Fasten the rear grill in place using the rear grill mounting nut.

Turn the nut clockwise and tighten firmly.

STEP 3.  Slide the fan blade, with the hollowed interior of the blade facing

towards the rear grill firmly onto the motor shaft. Make sure the

motor shaft pin lines up with the recessed groove in the back of

the fan blade.  Also, be sure the shaft protrudes from the front of

the blade.

STEP 4.  Secure fan blade onto the motor shaft by turning the blade cap

counter-clockwise (make sure the blade is firmly in position.)

STEP 5.  Install the front grill by snapping the circular front grill center

logo plate in place. 

STEP 6.  Center the front grill, aligning the Holmes logo so it is horizontal

and parallel to the floor, place onto the rear grill, and snap in

place. Secure by tightening the grill screw at the bottom of the

rear grill.

Insert the fan head neck joint (see figure #3) into

the hollow end of the top pole and slowly turn the neck joint to lock in

place. Be careful to align the cutaway/grooves on the neck joint with the

two protruding raised pieces inside the hollow end of the pole. Lastly,

insert the tilt adjustment knob into the neck joint and tighten until it is

securely in place.

DETACH FROM INSTRUCTIONS AND MAIL IN THIS FORM

Fill out form on reverse side or call 

to place your order today.

PLUS SHIPPING 

AND HANDLING

Page2

Page 3

A. LOGO PLATE (SNAP ON)
B. FRONT GRILL
C. BLADE CAP
D. FAN BLADE
E. REAR GRILL MOUNTING

NUT

F. PLASTIC BAND

G. GRILL SCREW
H. REAR GRILL
I. MOTOR SHAFT
J. GRILL MOUNT

K. SPEED CONTROL KNOB
L. OSCILLATION BAR
M. MOTOR HOUSING
N. TILT JOINT
O. TILT ADJUSTMENT KNOB
P. NECK JOINT
Q. HOLLOW END (FEMALE)
R. THREADED JOINT (MALE)
S. EXTENSION POLES
T. BASE COVER
U. WEIGHTED INSERT
V. BASE NUT

A

N

B

D

E

O

P

Q

R

S

T

F

G

H

I

M

J K

L

(fig 3)

U

V

(fig 1)

POLE

THREADED JOINT 

(male end)
HOLLOW END OF 

BASE COVER

ON TOP

BASE COVER

WEIGHTED INSERT

BASE NUT

CUTAWAY/
GROOVES

▼

CUTAWAY/ GROOVES

HOLLOW END

(female end)

THREADED JOINT

(male end)

(fig 2)

C