Carrier 33PILOT-01 사용자 설명서

3

MODIFY — Like the INC/DEC buttons, this rotary knob modi-

fies the value of the highlighted field within its defined limits. The

value increases or decreases with each increment of the rotary

knob. Turning the knob clockwise increases the value. Turning it

counterclockwise decreases the value. From the Zone Controller

Default screen, the MODIFY knob allows the user to modify the

set points.

The MODIFY rotary knob also functions as the SELECT

button when pressed.
SELECT — This button function varies according to the

screen that is currently displayed and the device to which the

System Pilot is attached. In general, the SELECT button

processes a user-selected option or initiates a new operation

mode for the System Pilot.
Zone Controller Occupancy Override — Pressing the SELECT

button for less than 3 seconds from the Zone Controller Default

screen while in an unoccupied mode will initiate an occupancy

override. While the occupancy status is blinking, the user can use

the INC/DEC buttons or the MODIFY rotary knob to adjust the

occupancy status.
System Pilot Alternate Maintenance Table — Pressing the

SELECT button for at least 3 seconds from the Zone Controller

Default screen will display the System Pilot Alternate Mainte-

nance Table (ALT_DISP).
Edit Mode — If the System Pilot is displaying editable data,

SELECT allows the user to MODIFY the point that the cursor

is positioned on.

If the EXIT button is pressed and the data on the screen has

been modified, the System Pilot displays the prompt “Save

data?” followed by the following softkeys: YES, NO and ESC.

The NAVIGATE rotary knob can be used to move between

YES, NO, and ESC (with wraparound). Position the cursor on

the desired softkey and press SELECT. Selecting YES causes

the System Pilot to write the new data to the controller and then

return to the next higher screen. Selecting NO returns the

System Pilot to the next higher screen without saving the new

data. Pressing Selecting ESCAPE or pressing the EXIT button

erases the “Save data?” prompt and causes the System Pilot to

remain in the current screen.
ATTACH SCREEN NAVIGATION — Pressing  SCROLL

UP and PAGE DOWN together for 3 seconds from any screen

will display the Attach screen.  If the data on the current screen

has been modified, the user will be prompted to save the data

as described above.  Exiting from the Attach screen without at-

taching will cause the System Pilot to display the Program

screen (not the screen from which the buttons were pushed).

If no user input is received for an

hour (i.e., if no buttons are pressed and no rotary knobs are

turned), the System Pilot reverts to the Default screen for its

default device. If connected to another device, the System Pilot

will re-attach to the default device.

To enter Program mode and display

the Program screen, press the SCROLL UP and SCROLL

DOWN buttons together for 3 seconds from the default screen.

The System Pilot will display one of the three program screens

shown in Fig. 6, depending on the security level that is speci-

fied in the System Pilot (PILOTCON) screen.
NOTE: Security level 1 programming is not normally available

for the end user and is not shown in this book. For information

regarding functions available with Security Level 1, refer to the

Installation and Configuration Instructions.

Use the SCROLL UP/SCROLL DOWN buttons or the

NAVIGATE knob to step through the options on the Program

screen. A description of the highlighted option will appear in

the bottom line of the screen and will indicate if the option is

not available. Press the SELECT button to select the currently

highlighted option. 

The following program screen options are available:

• ATTACH (all levels)

• Ctlr-ID (all levels)

• ALARM HIST (all levels)

• CONFIG (level 2 only)

• SETPOINTS (levels 2 and 3 only)

• SCHEDULES (level 2 only)

• DETACH (all levels)
ATTACH — Selecting the ATTACH option from the Program

screen displays one of the Attach screens shown in Fig. 7 and

8, according to whether the System Pilot is on the Carrier

communicating network or on the local bus.

The center portion of the screen shows the 8-character

controller name, bus number and element number for the

devices to which the System Pilot can attach. The first entry in

the list always displays the default device and shows “Default”

instead of the actual controller name.

The user can use the SCROLL UP/DOWN, NAVIGATE, or

PAGE UP/PAGE DOWN buttons to scroll through the list of

devices. To attach to a device, position the cursor on the device

and press SELECT.
NOTE: Editing the device list is restricted to security level 1.

If the System Pilot is already attached to the specified ad-

dress, the System Pilot will display the message “Reattach?”

followed by three softkeys displaying YES, NO, and ESC. Use

the NAVIGATE rotary knob to move between the soft keys and

press SELECT. The user can also press EXIT to erase the

prompt and remain in the Attach screen.

 If the System Pilot attaches to an un-addressed VVT®

Zone Controller, it will display the Zone Controller’s Ctlr-ID

screen as an indication to the user that the Zone Controller’s

address has not been set. This screen will show the controller

element number as 0, even though the controller will actually

be at its default    element number of 140. The user can press

EXIT to exit the System Pilot’s default screen. When the Sys-

tem Pilot attaches to an addressed Zone Controller, the System

Pilot will bring up the standard Zone Controller Default screen.

→

606

→

→

→