Audiovox ce506slk 사용자 가이드

-2-

-3-

-4-

-5-

-6-

-1-

Connect the loop aerial (provided) to the "AM
LOOP ANTENNA" snap terminals at the back
of the unit.

TO SEARCH FOR A STATION AUTOMATICALLY
Press and hold 

 button for 1 to 2 seconds, and the tuner starts

searching for a station for automatically. After tuning in to a station, the search stops.
The search may not stop at a station with a very weak signal.

TO RECEIVE THE FM BROADCAST IN STEREO
When the reception is good, the "STEREO" indicator will appear on the display.

Fully unwind the wire antenna. Then extend
the wire antenna and place it in the position
that sounds best.
NOTE: DO NOT CONNECT TO AN OUTSIDE
ANTENNA.

1. Set to the desired band and station.

PRESETTING STATION
You may tuned in to a stored station directly by entering the preset number. It is possible to store
stations of any band in your choice order.

Manual memory presetting
This feature allows you to manually preset stations to any desired channel.

2. Press 

  MEMORY button, the MEMORY

indicator blinks.

3. Press 

 REPEAT/PRESET button to

select a channel number for the preset
station.

4. Press   MEMORY button to memorize the

station.

5. Repeat steps 1 to 4 for the next preset.

1. If you want to exit snooze mode, press   POWER button to turn on the system.

2. The preset auto play timer function will be active every day if it is not cancelled.

To cancel timer play function, press and hold TIMER button about 3 seconds until "TIMER"
indicator disappears on the display.

1. In standby mode, press DISPLAY button

and you can check the auto play timer if it
has been set.

2. In power on mode, press DISPLAY button

repeatedly and you also can check
system status, clock and auto play timer
if they have been set.

1. Press SLEEP button while the power is on.

"SLEEP 90" appears on the display.
Note: SLEEP can be adjusted in TUNER,
CD and AUX modes.

SLEEP SETTING
When the sleep timer is used, the power is automatically turned off after the specified time passes.

2. Press SLEEP button repeatedly to select the

length of remaining time until the unit turns
off.
It changes the indicator in the following way:

If the sleep timer is set, the word "SLEEP" will
be shown on the display.
To cancel the sleep timer, press SLEEP button
once and "SLEEP" disappears on the display.

NOTE: Once the sleep time reaches, the power will be turned off atuomatically.

1. Press FUNCTION button to TUNER.

2. Press   STOP/BAND button to select your

desired band (FM/AM).

3. Press 

buttons to select a station.

The power can be turned on automatically at a preset time so that you can wake up CD or
RADIO  function.

Make sure the clock is correct before TIMER PLAY. Please refer to CLOCK setting procedures.

Note: The unit must be in 'STANDBY' mode to set the timer.

1. Press and hold TIMER  button until the

"TIMER" indicator blinks on the display.

2. While "TIMER" indictor blinks on the

display, press and hold   MEMORY button
about 3 seconds until hour blinks on the
display.

3. Press 

buttons to set hour.

4. Press   MEMORY button. The minute will

blink.

5. Press 

buttons to set minutes and press 
MEMORY button to confirm, finally
"TIMER" indicator will stop blinking after
several seconds.

6. Turn on the unit to select the desired

program source by pressing FUNCTION
button.
TUNER: select a BAND and a station
CD:

Insert a disc

9. If you want to snooze a few more minutes.

You can press SNOOZE button (on the
Remote Control), the system will go to
standby mode ("SNOOZE" indicator
appear on the display) and then turn on
again 5 minutes later.

You can repeat this function as many as you
desired within 60 minutes from the preset
automatically PLAY timer.

7. Set volume level and X-Bass, and then

press   POWER button to standby mode.

8. When the preset time reaches, the system

will turn on automatically and "TIMER"
indicator will blink on the display.

Press   POWER button, the POWER ON indicator will light up. Select the desired function by
pressing FUNCTION button and the corresponding function indicator will be shown on the display.

Press 

  POWER button to STANDBY, the POWER ON indicator will go out and only clock

display  will be shown.

1. In standby mode, press and hold 

MEMORY button until the time blinks on the
display.

5. Press 

 MEMORY button, the MINUTE

blinks.

6. Press 

buttons to set correct minutes, and then
press 

 MEMORY button to start the

clock.

2. Press 

buttons to set 12 Hour or 24 Hour
timer format.

3. Press   MEMORY button, the hour  blinks.

4. Press 

buttons to set correct hour.

X-BASS is designed specifically to boost the
low frequency sound to obtain a more powerful
bass.
Note: Press X-BASS button, the  indicator of
X-BASS will light up.

FOR PRIVATE LISTENING
Connect the headphone (Ø3.5 mm stereo mini-plug) to the PHONES jack.
When headphones are connected, the speakers are automatically disconnected.

-BASS

 CD DOOR OPEN/CLOSE button

 PLAY/PAUSE button

PHONES jack

 TUNING   / 

 SKIP 

 button

 STOP/BAND / 

 REPEAT/PRESET

button

 MEMORY button

RANDOM button

SLEEP/TIMER/DISPLAY button

FUNCTION (CD/TUNER/AUX)/INTRO

button

10. VOLUME (-/+) controls

11. X-BASS indicator

12. X-BASS button

13.

 POWER button

14. POWER ON indicator

15. LCD display

16. Remote sensor

17. CD door

18. FM Antenna wire

19. AM Loop Antenna

20. AC cord

21. AUX IN jack

22. Stand (optional)

1

3

2

4 5 6 7

8

9

10 1112 13 14

15

16

17

18 19

20

21

22

Follow the advice below for safe and appropriate operations.

ON PLACEMENT
•

Do not use the unit in places which are
extremely hot, cold, dusty or humid.

•

Place the unit on a flat and even surface.

•

Do not restrict the air flow of the unit by
placing it in a place with poor air flow, by
covering it with a cloth, or by placing it on
a carpet.

ON SAFETY
•

When connecting and disconnecting the
AC cord, grip the plug and not the cord
itself. Pulling the cord may damage it and
create a hazard.

•

When you are not going to use the unit
for a long period of time, disconnect the
AC power cord.

ON AC VOLTAGE
•

Before use, check that the rated voltage
of your unit matches your local voltage.

VENTILATION WARNING
•

The normal ventilation of the product shall
not be  impeded for intended use.

ON CONDENSATION
•

When left in a heated room where it is
warm and damp, water droplets or
condensation may form inside the CD
player.

•

When there is condensation inside the
unit, the unit may not function normally.

•

Let it stand for 1 to 2 hours before turning
the power on, or gradually heat the room
up and dry the unit before use.

AUX JACK
•

To listen to audio
signals from external
unit through this unit:
Connect the red plug
to the R jack, and the
white plug to the L jack
of the AUX in
connector.

FCC INFORMATION (For USA ONLY)
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in
a particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of  the following
measures:

- Reorient or relocate the receiving

antenna.

- Increase the separation between the

equipment and receiver.

- Connect the equipment into an outlet

that is on a circuit different from the one
the receiver is connected.

- Consult the dealer or an experienced

radio/TV technician for help.

You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.

(on left side

of the unit)