Denon AVR-1403 작동 가이드
46
ENGLISH
19 TROUBLESHOOTING
If a problem should arise,first check the following.
1. Are the connections correct ?
2. Have you operated the receiver according to the Operating Instructions ?
3. Are the speakers, turntable and other components operating property ?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.
Disconnect the power immediately and contact your store of purchase.
1. Are the connections correct ?
2. Have you operated the receiver according to the Operating Instructions ?
3. Are the speakers, turntable and other components operating property ?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.
Disconnect the power immediately and contact your store of purchase.
Symptom
Cause
Measures
Page
DISPLAY not lit and sound not produced
when power switch set to on.
when power switch set to on.
• Power cord not plugged in securely.
• Check the insertion of the power cord plug.
• Turn the power off with the remote control
• Turn the power off with the remote control
unit after turning the POWER operation
switch on.
switch on.
9
24
DISPLAY lit but sound not produced.
• Speaker cords not securely connected.
• Improper position of the audio function
• Improper position of the audio function
button.
• Volume control set to minimum.
• MUTING is on.
• Digital signals not input Digital input
• MUTING is on.
• Digital signals not input Digital input
selected.
• Connect securely.
• Set to a suitable position.
• Set to a suitable position.
• Turn volume up to suitable level.
• Switch off MUTING.
• Input digital signals or select input jacks to
• Switch off MUTING.
• Input digital signals or select input jacks to
which digital signals are being input.
13, 14
25
26
27
26
27
26
DISPLAY not displayed and the
“ON/STANDBY” LED flashes at a high
rate
“ON/STANDBY” LED flashes at a high
rate
• Speaker terminals are short-circuited.
• Block the ventilation holes of the set.
• The unit is operating at continuous high
power conditions and/or inadequate
ventilation.
ventilation.
• Switch power off, connect speakers
properly, then switch power back on.
• Turn off the set’s power, then ventilate it
well to cool it down.
Once the set is cooled down, turn the
power back on.
Once the set is cooled down, turn the
power back on.
• Turn off the set’s power, then ventilate it
well to cool it down.
Once the set is cooled down, turn the
power back on.
Once the set is cooled down, turn the
power back on.
13, 14
5, 14
5, 14
Sound produced only from one channel.
• Incomplete connection of speaker cords.
• Incomplete connection of input/output
• Incomplete connection of input/output
cords.
• Connect securely.
• Connect securely.
• Connect securely.
13, 14
9 ~ 14
Positions of instruments reversed during
stereo playback.
stereo playback.
• Reverse connections of left and right
speakers or left and right input/output
cords.
cords.
• Check left and right connections.
13, 14
This unit does not operate properly when
remote control unit is used.
remote control unit is used.
• Batteries dead.
• Remote control unit too far from this unit.
• Obstacle between this unit and remote
• Remote control unit too far from this unit.
• Obstacle between this unit and remote
control unit.
• Different button is being pressed.
• < and > ends of battery inserted in reverse.
• < and > ends of battery inserted in reverse.
• Replace with new batteries.
• Move closer.
• Remove obstacle.
• Move closer.
• Remove obstacle.
• Press the proper button.
• Insert batteries properly.
• Insert batteries properly.
15
15
15
15
15
—
15
Common problems arising when listening to the
CD, records, tapes, and FM broadcasts, etc.
Remote control unit.
Note:
When a subwoofer has been connected and the virtual surround function is being used, the signal played from the subwoofer channel is LFE
only (only when playing Dolby Digital or DTS signals) for initial factory settings (i.e., the setting of the front speaker is “LARGE” and the setting
of the subwoofer mode is “NORM”).
When subwoofer effects are felt to be weak, while in the system setup mode try setting the subwoofer mode to “+MAIN”, or the front speaker
to “SMALL” in the Speaker Configuration settings.
Making these settings will result in the low-frequency sounds of the front channel being played from the subwoofer.
When a subwoofer has been connected and the virtual surround function is being used, the signal played from the subwoofer channel is LFE
only (only when playing Dolby Digital or DTS signals) for initial factory settings (i.e., the setting of the front speaker is “LARGE” and the setting
of the subwoofer mode is “NORM”).
When subwoofer effects are felt to be weak, while in the system setup mode try setting the subwoofer mode to “+MAIN”, or the front speaker
to “SMALL” in the Speaker Configuration settings.
Making these settings will result in the low-frequency sounds of the front channel being played from the subwoofer.