Sony DSC-T1 작동 가이드

4 Disconnect the USB cable.

For details, see page 80 or 86 of Operating Instructions supplied with the 
camera.

1 Mount the just formatted 

• If you insert the “Memory Stick Duo” 

without first mounting it in a Memory 
Stick Duo Adaptor, you may be unable 
to remove the “Memory Stick Duo”.

2 Copy the DSCT1V2.ash file in the CD-ROM to the “Memory Stick 

3 Remove the “Memory Stick Duo”.

2

1 Insert the “Memory Stick Duo” into the camera.
2 Connect the AC Adaptor (supplied) to the USB cradle (supplied) 

3 Connect the camera to the USB cradle.

• Disconnect the USB cable if it is connected.
• Use the AC Adaptor to prevent the power from cutting off partway through the 

procedure.

• The battery pack cannot be used for this procedure.

1

1 Set the mode switch to 

2 Press the POWER button while holding down MENU, and turn on 

2

1 Press MENU.

The menu appears.

2 Press B on the control button to select 

B again.
The Setup screen appears.

3 Press V on the control button to select 

(Setup 2).
“Version: 1” appears.

• When “Version: 1” does not appear, turn off the camera, then 

perform the procedure again starting from “Setting the 
update mode”.

• When “Version: 2” appears, the camera has already been 

updated and there is no need to update the version.

3

1 Press B/V on the control button to select 

[Version], then press B.

2 Press v/V on the control button to select 

[Update], then press z.
“Access” appears.

If the following errors occur at this time:
“ERROR 20: No software file” appears.
Cause: The file is not present in the “Memory Stick Duo”.
Remedy: Check the contents of the “Memory Stick Duo” with the computer, 
then perform the procedure again starting from “Software updating 
instruction”.
“ERROR 30: Format Memory Stick before use” appears.
Cause: There are multiple files and folders in the “Memory Stick Duo”.
Remedy: Format the “Memory Stick Duo” with the camera and perform the 
procedure again starting from “Preparing the update firmware”.
“ERROR 40: Invalid file” appears.
Cause:
– The file in the “Memory Stick Duo” is not correct.
– The firmware version is the same or older than the existing one.
– The update target model is different.
Remedy: Check the current version, then return to the top page, select and 
download the correct firmware, and perform the procedure again starting from 
“Software updating instruction”.

4

Check the current version and the updated 
version, then press v on the control button to 
select [OK], and press z.

The “Software Update” screen appears.
Select [Cancel] to return to the Setup screen.

5

Press v on the control button to select [OK], then press z.

Updating starts.

6

The “Updating” screen appears and the a indicators flash.
When all three indicators change from flashing to lit, the updating is complete.

• Updating takes a number of minutes (normally about 1 minute).

If the following errors occur at this time:
aaa do not flash for 30 seconds or more at the “Updating” 
screen.
Cause: Version updating may have failed.
Remedy: Follow the steps in “Re-update procedure” and perform the update 
again.

“ERROR 10: Error” appears.
Cause: Version updating may have failed.
Remedy: Follow the steps in “Re-update procedure” and perform the update 
again.

7

The “Finished” screen appears. Turn off the camera.
Be sure to press the RESET button after turning off the power. (When you 
press the RESET button, the date/time and other settings are canceled.)

8

Check 

 (Setup 2) at the Setup screen to make sure 

that the version has been updated.
If the version has been updated to “2”, the procedure is 
complete.
After finishing the update, format the “Memory Stick Duo” to delete the 
update file.

When updating fails, follow the procedure below and perform re-update.

1 Turn off the camera and check 

• You cannot use a “Memory Stick PRO 

Duo” for this re-update procedure.

2 Wait for 5 seconds or more, then 

turn on the camera. 
Re-update starts, and the access lamp 
on the camera lights up.
After about one minute, the access 
lamp turns off and the update is complete.

• When performing re-update, nothing appears on the LCD screen, but the update 

is being performed.

3 Turn off the camera.

Be sure to press the RESET button after turning off the power. (When you 
press the RESET button, the date/time and other settings are canceled.)

4 Follow the procedure in “Checking the updated version” and 

check the firmware version.
Press the POWER button while holding down MENU, then check 

 (Setup 

2) at the Setup screen to make sure that the version has been updated.
If the version has been updated to “2”, the procedure is complete.

If the following error occurs at this time:
The access lamp on the camera flashes or lights up during re-
update, but does not turn off even after 3 minutes or more have 
passed.
Cause: Trouble occurred with the “Memory Stick Duo” during updating.
Remedy: Consult your nearby Sony service center or service facility.

• Microsoft and Windows are either registered trademarks or trademarks of the U.S. 

Microsoft Corporation in the United States and/or other countries.

• Macintosh and Mac OS are trademarks or registered trademarks of Apple Computer, 

Inc.

• In addition, system and product names used in this manual are, in general, trademarks 

or registered trademarks of their respective developers or manufacturers.

m

<

<