Whirlpool mede300 사용자 설명서

■

The Wrinkle Shield Steam feature is not available on Delicate 
or Super Delicate Automatic Cycles and Timed Cycles with 
Low, Extra Low, and Air Only Temperature selected. WRINKLE 
SHIELD™ without Steam cycle is available for these cycles.

■

For the Casual Cycle, the WRINKLE SHIELD™ STEAM feature 
is preset to “ON.” The other cycles will retain the WRINKLE 
SHIELD™ STEAM feature setting. 

The End of Cycle Signal produces an audible sound when the 
drying cycle is finished. 
Press until the desired volume (Loud, Soft, or Off) glows green.
NOTE: When the WRINKLE SHIELD™ STEAM feature is selected 
and the End of Cycle Signal is on, an audible sound will be 
emitted every 5 minutes until the clothes are removed, or the 
WRINKLE SHIELD™ STEAM feature is finished.

You can change the volume of the sound of the beeps. Press until 
the desired volume (Loud, Soft, or Off) glows green. The Power 
and Cancel buttons will still beep softly even when the Button 
Sound volume is set to Off.   

When pressed during a cycle, the Drum Light turns on and will 
remain on until pressed again, the door is opened and closed, or 
the door is left open for 20 minutes.

Press and hold the CONTROLS LOCK/UNLOCK button for 
3 seconds. The control is locked when a single beep is heard and 
the Controls Lock status light is on. This feature allows you to lock 
your settings to avoid unintended use of the dryer. You can also 
use the Controls Lock feature to avoid unintended cycle or option 
changes during dryer operation.

■

When the dryer is off, it is not necessary to press the Control 
On button before activating the Controls Lock feature. 

Press and hold the CONTROLS LOCK/UNLOCK button for 
3 seconds to turn this feature off. 
NOTE: When the dryer is running and Controls Lock is on, the 
dryer can be stopped by pressing the Pause/Cancel button, but 
cannot be restarted until the control is unlocked.

You can change Auto Cycles, Timed Cycles, Options, and 
Modifier, and anytime before pressing Start. 

■

Three short tones sound if an unavailable combination is 
selected. The last selection will not be accepted.

1. Press PAUSE/CANCEL twice. This ends the current cycle.
2. Select the desired cycle and options.
3. Press and hold START. The dryer starts at the beginning of the 

new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the 
cycle, the dryer automatically shuts off.

You can change an Option or Modifier anytime before the selected 
Option or Modifier begins.
1. Press PAUSE/CANCEL once.
2. Select the new Option and/or Modifier.
3. Press and hold START to continue the cycle.
NOTE: If you happen to press Pause/Cancel twice, the program 
clears and your dryer shuts down. Restart the selection process.

If all your loads on all Auto Dry cycles are consistently not as dry 
as you would like, you may change the preset Dryness Level 
settings to increase the dryness. This change will affect all of your 
Auto Dry cycles.
Your Dryness Level settings can be adjusted to adapt to different 
installations, environmental conditions or personal preference. 
There are 3 drying settings: 1 (factory preset dryness level), 
2 (slightly drier clothes, approximately 15% more drying time), 
and 3 (much drier clothes, approximately 30% more drying time). 
1. The Dryness Level settings cannot be changed while the dryer 

is running.

2. Press and hold the Dryness Level button for 5 seconds. The 

dryer will beep, and “CF” will be displayed for 1 second 
followed by the current drying setting.

3. To select a new drying setting, press the Dryness Level key 

again until the desired drying setting is shown. 
NOTE: While cycling through the settings, the current setting 
will not flash, but the other settings will flash.

4. Press START to save the drying setting.
5. The drying setting you selected will become your new preset 

drying setting for all Auto Dry cycles.