poly-planar mz-100 사용자 가이드
Poly Planar Group LLC - 520 McCormick Dr. - Glen Burnie MD 21061 - 410-761-4000
- 6 -
Connecting the MZ-100 Input (Fixed Gain):
For operation without the optional external volume control, connect the amplifier
inputs to the VARIABLE LINE OUT of your receiver using shielded RCA patch
cables. In this case the amplifier volume will be determined by the volume setting
of the source component.
inputs to the VARIABLE LINE OUT of your receiver using shielded RCA patch
cables. In this case the amplifier volume will be determined by the volume setting
of the source component.
Connecting the MZ-100 Input (Variable Gain):
For operation with the external volume control, connect the amplifier inputs to the
PRE-AMP LINE OUT of your receiver using shielded RCA patch cables. The
Pre-amp line output should be a fixed level output that is independent of the
volume setting of the receiver.
PRE-AMP LINE OUT of your receiver using shielded RCA patch cables. The
Pre-amp line output should be a fixed level output that is independent of the
volume setting of the receiver.
To VARIABLE line output of receiver, TV,
or other audio source.
or other audio source.
Figure 4 - Input connections without Volume control
Figure 5 - Input connections with Volume control
Volume
Control
Control
NOTE:
The BLUE remote wire
should be switched or
connected to an
accessory circuit
NOTE:
The BLUE remote wire should be tied to
12V (Red wire). The amp can be turned
off by turning the volume knob all the
way down.
Poly Planar Group LLC - 520 McCormick Dr. - Glen Burnie MD 21061 - 410-761-4000
- 7 -
Poly-Planar
Bass 0
Bass 0
Poly-Planar
Treb 0
Treb 0
Poly-Planar
Space 0
Space 0
Poly-Planar
Vol 15
Vol 15
Poly-Planar
LoudON
LoudON
Poly-Planar
LimON
LimON
Poly-Planar
EQ ON 2
EQ ON 2
Rotate VOLUME control to
set the AUDIO parameters
set the AUDIO parameters
Connecting the MZ-100 to an RD-44 control panel:
The MZ-100 can be controlled by the RD-44 control panel. Using an extension
cable (not shown) the panel can be up to 60 feet away from the amplifier. Plug
the RD-44 or its extension cable into the CONTROL PANEL plug on the MZ-100.
Be sure to tighten the waterproof connectors.
cable (not shown) the panel can be up to 60 feet away from the amplifier. Plug
the RD-44 or its extension cable into the CONTROL PANEL plug on the MZ-100.
Be sure to tighten the waterproof connectors.
Controls and Screens when Connected to an RD-44 control panel
Screen
Button Description
Power On start-up screen
Volume is displayed 0 min – 31 max
Push 1 time to adjust Bass
( -9 min to + 9 max, 0 = flat )
Push 2 times to adjust Treble
( -9 min to + 9 max, 0 = flat )
Push 3 times to adjust Stereo Spatial
Enhancement
0 = normal, 1 = wide, 2 = widest
Push 4 times to set Loudness ON/OFF
Enhances bass at low volumes
Push 5 times to set Limiter ON/OFF
ON prevents distortion at high volume
Push 6 times to set Equalizer ON/OFF
ON enables the equalizer selected by
the switches shown on page 5.
Volume is displayed 0 min – 31 max
Push 1 time to adjust Bass
( -9 min to + 9 max, 0 = flat )
Push 2 times to adjust Treble
( -9 min to + 9 max, 0 = flat )
Push 3 times to adjust Stereo Spatial
Enhancement
0 = normal, 1 = wide, 2 = widest
Push 4 times to set Loudness ON/OFF
Enhances bass at low volumes
Push 5 times to set Limiter ON/OFF
ON prevents distortion at high volume
Push 6 times to set Equalizer ON/OFF
ON enables the equalizer selected by
the switches shown on page 5.
IMPORTANT NOTE:
The BLUE remote wire should
be tied to 12V (Red wire).