KitchenAid 29.5 cu. ft 48-Inch Width Built-In Side by Side Refrigerator with PrintShield™ Finish 사용 및 관리

If it is almost time to change the filter:

The status light will automatically illuminate and will remain on,

appearing yellow. The words “ORDER FILTER” will appear on

the display screen. Press FILTER to see what percentage of your

filter’s life remains. You should order the appropriate replacement

filter. See “Accessories.”

If it is time to change the filter:

The status light will remain on, changing to red. The words

“REPLACE FILTER” and “HOLD BUTTON TO RESET” will appear

on the display screen until the filter has been changed and the

status light has been reset.

To reset the water filter status light:

After changing the filter, reset the status light by pressing and

holding the FILTER button for 3 seconds. The status light will

blink red and change to blue, and then turn off when the system

is reset.

Ice Maker and Storage Bin

(on some models - Accessory)

IMPORTANT: Flush the water system before turning on the

ice maker. See “Water and Ice Dispensers.” Allow 24 hours to

produce the first batch of ice. Discard the first three batches of

ice produced. Allow 3 days to completely fill the ice container.

Style 1

To Turn the Ice Maker On/Off:
The On/Off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

2. To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

To Remove and Replace the Ice Bin:

1. Flip up the covering panel.

A. Ice maker cover

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull the ice bin forward.

4. Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

Style 2

To Turn the Ice Maker On/Off:
The On/Off switch is located on the top right side of the freezer

compartment.

1. To turn the ice maker on, slide the control to the ON (left)

position.

NOTE: Your ice maker has an automatic shutoff. The ice

maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

2. To manually turn the ice maker off, slide the control to the OFF

(right) position.

To Remove and Replace the Ice Storage Bin:

1. Hold the base of the storage bin with both hands and press

the release button to lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to

the OFF (right) position when removing the storage bin. The

sensor cover (“flipper door”) on the left wall of the freezer

stops the ice maker from producing ice if the door is open or

the storage bin is removed.

2. Replace the storage bin on the door and push down to make

sure it is securely in place.

Clean the Ice Storage Bin

NOTE: It is normal for ice to stick together in the ice bin. Ice may

be dispensed or used more frequently which will break up the ice.

It is recommended that the ice container be emptied and cleaned

as needed.
To clean the ice storage bin:

1. Empty the ice container. Use warm water to melt the ice if

necessary.

NOTE: Do not use anything sharp to break up the ice in the

bin or bucket. This can cause damage to the ice container

and the dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry

thoroughly. Do not use harsh or abrasive cleaners or solvents.