temco-tool 39rdvn 사용자 설명서
24
RDVN Series Direct Vent Gas Fireplace
20007628
Log Installation - 33RDVN
1. Open glass door (if installed).
2. Remove logs from the packaging. (As with all plastic,
2. Remove logs from the packaging. (As with all plastic,
these bags are not toys and should always be kept
away from children and infants.)
away from children and infants.)
3. Place rear log on back bracket. Ensure that log is
firmly positioned and there is no side-to-side move-
ment.
ment.
4. Place the front log on the front burner (starting to-
ward the rear of the front burner) and slide it forward
until the notches lock into place.
until the notches lock into place.
5. Place the top logs onto the locator notches. Ensure
that the logs are secure. (Fig. 42)
Installation of Logs, Lava Rock & Ember Material
Unpack the logs from packaging and remove each log
from its wrapping materials.
from its wrapping materials.
The logs are fragile and should be handled
with care. Keep the packaging material out
of the reach of children and dispose of the
material in a safe manner.
with care. Keep the packaging material out
of the reach of children and dispose of the
material in a safe manner.
The embers supplied with your fireplace
are made from platinum coated embers
and should be handled carefully. Wash
your hands immediately after touching
to avoid irritation. The embers must be
placed correctly in order to function
properly.
are made from platinum coated embers
and should be handled carefully. Wash
your hands immediately after touching
to avoid irritation. The embers must be
placed correctly in order to function
properly.
Log Installation - 36/39RDVN
Attention: Glass door should be removed when install-
ing logset and prior to lighting the unit.
1. Remove glass door (Refer to “Window Frame Re-
ing logset and prior to lighting the unit.
1. Remove glass door (Refer to “Window Frame Re-
moval”).
2. Remove logs from carton and inspect. Refer to Fig-
ure 43.
3. Rear log should be installed onto rear log supports.
Match up slots on rear of log with the vertical log
bracket tabs. Push log back as far as it will go.
bracket tabs. Push log back as far as it will go.
4. The front log should be placed on the front log sup-
ports, slots aligned with tabs and log bottom in chan-
nel.
nel.
5. Top twigs can then be placed in their designated po-
sitions provided with pins on back logs and grooves
on the front log. Front log must be upright.
on the front log. Front log must be upright.
TL126
33RDVN logs
9/04
Fig. 42 33RDVN log placement.
TL126
TL119
DV1000/DV1200
logs
12/11/03 djt
TL119
Fig. 43 Correct log placement for 36/39RDVN.
All Models
6. Place platinum embers loosely along top surface
6. Place platinum embers loosely along top surface
of burner along entire length of ported area of front
burner. DO NOT place embers on back portion of
burner. Use individual pieces of embers no larger
than dime size, about 1/16” thick (fluffed up thick-
ness). Use a single layer of embers and DO NOT
overlap pieces. Ember material should be fluffed up
and not compressed. When properly placed, all em-
bers will glow red. Adding more embers than neces-
sary will detract from appearance.
burner. DO NOT place embers on back portion of
burner. Use individual pieces of embers no larger
than dime size, about 1/16” thick (fluffed up thick-
ness). Use a single layer of embers and DO NOT
overlap pieces. Ember material should be fluffed up
and not compressed. When properly placed, all em-
bers will glow red. Adding more embers than neces-
sary will detract from appearance.