Philips fw-c785 사용자 설명서
26
English
1
Press and hold CLOCK•TIMER for more than
two seconds to select timer mode.
➜ "
two seconds to select timer mode.
➜ "
AM 12:00" or "00:00" or the last timer
setting will start flashing.
➜
TIMER
will start flashing.
➜ The selected source will be lighted while
other available sources are flashing.
2
Press CD, TUNER or TAPE to select the
desired source.
desired source.
●
Before setting timer, make sure the music source
has been prepared.
CD – Load the disc(s).To start from a specific
track, make a programme (refer to “CD
Operation - Programming the disc tracks”).
TUNER – tune to the desired radio station.
TAPE – load the prerecorded tape into tape
deck 2.
has been prepared.
CD – Load the disc(s).To start from a specific
track, make a programme (refer to “CD
Operation - Programming the disc tracks”).
TUNER – tune to the desired radio station.
TAPE – load the prerecorded tape into tape
deck 2.
3
Press à or á on the system repeatedly to set
the hour for the timer to start.
the hour for the timer to start.
4
Press í or ë on the system repeatedly to set
the minute for the timer to start.
the minute for the timer to start.
5
Press CLOCK•TIMER to store the start time.
➜ "
➜ "
TIMER ON" will be displayed and followed
by the set timer "
XX:XX" and then the
selected source.
➜
TIMER
will remain on the display.
●
At the preset time, the selected source will play.
To exit without storing the setting
●
Press Çon the system.
Notes:
– If the selected source (CD) is not available when
preset timer is reached,TUNER will be selected
automatically.
– During timer setting, if no button is pressed
within 90 seconds, the system will exit timer setting
mode automatically.
– If the selected source (CD) is not available when
preset timer is reached,TUNER will be selected
automatically.
– During timer setting, if no button is pressed
within 90 seconds, the system will exit timer setting
mode automatically.
To deactivate the TIMER
●
Press TIMER ON/OFF on the remote control.
➜ The display will show "
➜ The display will show "
CANCEL" and
TIMER
will disappear from the display.
To activate the TIMER
●
Press TIMER ON/OFF on the remote control.
➜ The last set timer information will be shown
➜ The last set timer information will be shown
for a few seconds and
TIMER
will appear
on the display.
Sleep Timer Setting
The sleep timer enables the system to switch to
Standby mode automatically at a preset time.
Standby mode automatically at a preset time.
1
Press SLEEP on the remote control repeatedly
to select a preset time.
➜ The selections are as follows (time in
to select a preset time.
➜ The selections are as follows (time in
minutes):
15 ™ 30 ™ 45 ™ 60 ™ OFF ™ 15 …
15 ™ 30 ™ 45 ™ 60 ™ OFF ™ 15 …
➜ "
SLEEP XX" or "OFF" will be displayed. "XX"
is the time in minutes.
2
When you reach the desired length of time, stop
pressing the SLEEP button.
➜
pressing the SLEEP button.
➜
SLEEP
will appear on the display, except for
"
OFF" mode.
➜ The Sleep Timer is now set. Before the system
switches to standby mode, a countdown of 10
seconds will be displayed.
"
seconds will be displayed.
"
SLEEP 10" ™ "SLEEP 9".... ™ "SLEEP 1"
™ "
SLEEP"
While SLEEP mode is activated
To check the remaining length of time
●
Press SLEEP once.
To change the preset sleep timer
●
Press SLEEP twice.
➜ The display will show the remaining time
➜ The display will show the remaining time
followed by the sequence of sleep timer
options.
options.
To deactivate the Sleep Timer
●
Press SLEEP repeatedly until "
OFF" is displayed,
or press the STANDBY ON button.
Clock/Timer
pg 01-30/C785/34-Eng 12/27/01 10:19 AM Page 26