GE 17254 사용자 설명서

You may also store CID information in the phone’s internal memory. 

1. Make sure the phone is 

OFF (not in talk mode).

2.  Use the CALLER ID-VOLUME (5or6) button to scroll to the desired CID 

record.

3.  Press the mem button.
4.  Use the touch-tone pad to enter a memory location (0-9) to store the 

number in that memory location. You will hear a confirmation tone. 

MEMO? is displayed, and you must confirm replacement by 

display UNABLE TO STORE.

1.  Repeat steps 1 through 3 in Storing CID Records in Internal Memory. After 

you enter the memory location, 

REPLACE MEMO? shows in the display.

2. Press the mem button again, and the new CID record replaces the old 

memory in that location. You will hear a confirmation tone.

1.  Make sure the phone is 

OFF (not in TALK mode).

2.  Use the CALLER ID-VOLUME (5or6) button to display the CID record you 

want to delete.

3.  Press chan/delete. The display shows 

4.  Press chan/delete again to erase the record and 

DELETED shows in the 

display. You will hear a confirmation tone.

1.  Make sure the phone is 

OFF (not in TALK mode).

2.  Use the CALLER ID-VOLUME (5or6) button to display any Caller ID 

record.

3.  Press and hold the chan/delete button until 

DELETE ALL? shows in the 

display.

4.  Press chan/delete again to erase all records. You will hear a confirmation 

tone. The display shows 

Each handset can store up to ten 24-digit numbers with up to 15-character 

names in memory for quick dialing. This memory feature is in addition to the 

CID memory log, which stores up to 40 CID records in each handset.

1.  Make sure the phone is 

OFF (not in TALK mode).

2.  Press the mem button.
3.  Press the desired memory location (0 through 9) or use  

CALLER ID-VOLUME (5or6) to scroll to the desired memory location.

EMPTY shows in the display.

4. Press the mem button again. The display shows 

ENTER  NAME.

5.  Use the touch-tone pad on the handset to enter the name (up to 15 

characters) and press the memory button to save. More than one letter 

is stored in each of the number keys. For example, to enter the name Bill 

Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the 

letter I. Press the 5 key 3 times for the letter L. Wait for one second. Press 

the 5 key 3 times for the second letter L. Press the 1 key to insert a space 

between the L and the S. Press the 7 key 4 times for the letter S; press the 

6 key once for the letter M; press the 4 key 3 times for the letter I; press the 

8 key for the letter T; press the 4 key twice for the letter H.

6.  Press the mem button to save the name. The display shows 

NUMBR.

7.  Use the touch-tone pad to enter the telephone number you want to store 

(up to 24 digits). 

8.  Press mem again to store the number. You will hear a confirmation tone.

1. Repeat steps 1 through 6 in Storing a Name and Number in Memory.
2. Press the redial button.
3.  Press the mem button to store the number. You will hear a confirmation 

tone.

To replace an old number with a new redial number:
1.  Repeat steps 1 through 6 in Storing a Name and Number in Memory.
2.  Press the redial button.
3.  Press the mem button, and 

REPLACE MEMO? shows in the display.

4.  Press the mem button again to replace the old number with the new 

number. You will hear a confirmation tone.

If a pause is needed to wait for a dial or access tone, press the #PAUSE/

ringer button to insert a delay in dialing sequence of a stored number (for 

example, after you dial 9 for an outside line, or to wait for a computer access 

tone). Pause shows in the display as a P, and each pause counts as one digit 

in the dialing sequence.

1.  Repeat steps 1 through 7 in Storing a Name and Number in Memory.
2.  Press the mem button, and 

REPLACE MEMO? shows in the display.

3.  Press the mem button to store the number. You will hear a confirmation 

tone.

1.  To review stored numbers, press the mem button, and use the CALLER 

ID-VOLUME (5or6) button to scroll to the memory location, or press the 

corresponding number key for a desired memory location (0-9).

2.  When the number that you want to delete shows in the display, press the 

chan/delete button. The display shows 

3.  Press chan/delete again to delete the data. The display shows 

DELETED.

1.  Make sure the phone is 

ON by pressing the TALK/CALL BACK button.

2.  Press the mem button.
3.  Press the memory location (0-9). The number dials automatically.
   

 - OR -

1.  Make sure the phone is 

OFF (not in TALK mode).

2.  Press the mem button.
3.  Use the touch-tone pad or the  CALLER ID-VOLUME (5or6) button to 

scroll to the number you want to dial.

4.  Press the TALK/CALL BACK or SPEAKER button. The number dials 

automatically.

Use this feature to make calls which require a sequence of numbers, such as 

calling card calls to a frequently called long distance number. Each part of 

the sequence is dialed from memory. The following example shows you how 

to use chain dialing to make a call through a long distance service:
The Number for 

Long distance access number 

7

Authorization code 

8

Frequently called long distance number 

9

1.  Make sure the phone is 

ON (in TALK or SPEAKERPHONE mode).

2.  Press the mem button and then press 7.
3.  When you hear the access tone, press the mem button and then press 8.
4.  At the next access tone, press the mem button and then 9.

 This section discusses the buttons and features on the answering system.

The messages indicator shows you how many messages you have received, 

and blinks when there are new messages. The ans on/off button must be 

ON 

in order for the messages indicator to work.

1.  Wait for the caller to begin leaving a message (to determine who is 

calling).

2.  To speak to the caller, pick up the handset, and press the TALK/CALL BACK 

button.

The answering system automatically stops recording when you activate the 

handset or pick up an extension phone.

The messages indicator on the base lets you know when you have 

messages. To play messages, press PLAY/STOP. 
While a message is playing, you may do the following:
•  Press PLAY/STOP to stop the message playback.
•  Press and release 7 repeat to restart the current message; continue 

pressing and releasing 7 repeat to review previous messages.

•  Press and release 8 skip to go to the next message.

When the answering system memory is full, the system answers after 10 

rings. You should erase some messages so the answering system may 

record new messages.

You may erase messages three ways: one message at a time from the base; 

all messages from the base; or one message at a time from the handset or a 

phone in another location.
To erase one message at a time from the base:
•  Press PLAY/STOP. The message plays. 
•  Press and release the erase button.
To erase all reviewed messages from the base:
•  Press and hold the erase button until the unit beeps. 
To erase a message from the handset:
•  Press flash/answerer/call waiting button to enter into the handset remote  

access operation.

•  Press PLAY/STOP on the handset (the 2 button). The message plays.
•  Press erase (the 0 button) to erase the message during message playback.

Use the memo feature to leave a message.
1.  Press and hold the memo button on the base. 

2.  Begin speaking after you hear the beep.
3.  Release the memo button when finished.  

You may access the answering system with the cordless handset or from 

any tone-dial compatible telephone.

1.  Press the flash/answerer/call waiting button to access the answering 

system. 

2.  Use the corresponding handset keys just like you would use the base 

buttons (see Answering System Setup). The button functions are located 

on the handset above each number key. For example, to play messages: 

•  Press the flash/answerer/call waiting button. The display shows 

•  Press 2 (PLAY/STOP).
•  When you are finished listening to your messages, press the  

flash/answerer/call waiting button again.

Use the handset to screen calls even when you can’t hear the answering 

system. 
When the answering system picks up:
1.  Press the flash/answerer/call waiting button to access the answering 

system.

2.  Listen as the caller leaves a message.
3.  Press the TALK/CALL BACK button to speak to the person or press the 

flash/answerer/call waiting button to stop screening the call. 

When answering system memory is full, the system answers after 10 rings, 

beeps and waits for you to enter the 3-digit security code. If you don’t enter 

the security code within 10 seconds, the phone hangs up.
You should erase some messages so the answering system can record new 

ones.

•  Do not burn, disassemble, mutilate, or puncture. Like other batteries of 

this type, toxic materials could be released which can cause injury.

•  To reduce the risk of fire or personal injury, use only the 

Hydride (Ni-MH) battery listed in this User’s Guide.

•  Keep batteries out of the reach of children.
•   Remove batteries if storing over 30 days.

The following messages show the status of the phone or help you set up and 

use your phone.
ANSWERER REMOTE 

Indicates the handset is accessing the answering  

 

system.

BLOCKED CALL 

Caller information is blocked from transmission.

BLOCKED 

Caller name and number is blocked from  

 

NAME/NUMBER 

transmission. 

 

DELETE ALL? 

Prompt asking if you want to erase all Caller ID  

 

records.

DELETE CALL ID? 

Prompt asking if you want to erase the current  

 

Caller ID record that is shown on the display.

DELETE? 

Prompt asking if you want to erase one of the 10  

 

numbers stored in the phone’s outgoing  

 

memory.

DELETED 

Prompt confirming a CID record is erased.

DO NOT DISTURB 

Indicates DO NOT DISTURB function is turned on.  

 

Ringer and call screening is silenced.

EMPTY 

Indicates a memory location is vacant.

END OF LIST 

Indicates there is no additional information in  

 

the Caller ID memory log.

ENTER NAME 

Prompt telling you to name the handset or enter  

 

a name for one of the 10 memory locations.

INCOMPLETE 

Caller information is interrupted during  

 

DATA 

transmission or the phone line is excessively    

 

noisy.

LOW BATTERY 

Indicates the handset battery is low and needs  

 

charging.

NEW 

Indicates call or calls have not been reviewed.

NO DATA 

No Caller ID information was received.

NO CALLS  

Indicates no calls have been received.

PAGING FRM BASE 

Someone is paging the handset from the base.

PLEASE REGISTER 

Indicates the andset needs to be registered    

 

before use.

PRESS TALK KEY 

Indicates the CID number is a Directory Dial    

 

Number (DDN) and cannot be formatted.

Indicates the handset is registered and available  

 

for use.

REPT 

Repeat call message. Indicates that a new call  

 

from the same number was received more than  

 

once.

TRANSFERRING 

Indicates the call is being transferred from one  

 

handset to another.

UNABLE TO DIAL 

Indicates the CID or memory contents cannot be  

 

dialed.

UNABLE TO STORE  

Indicates the CID or memory contents cannot be  

 

stored.

UNAVAILABLE 

Indicates the handset is out of range. 

 

Or an additional handset is in use.  Or there has  

 

been a base power failure, in which case you 

 

must place all handsets on the main base cradle  

 

for 20 seconds to re-register.  

UNKNOWN 

The incoming call is from an area not serviced by  

NAME/CALLER/ 

Caller ID or caller information is not sent.

NUMBER 

Memory dialing

•  Make sure you correctly program the memory location keys.
•  Make sure you follow the proper dialing sequence.
•  You may need to reprogram numbers into memory after a power 

outage or  

battery replacement.

Out of range

•  Move closer to the base.
•  Reset the battery. Unplug the battery and plug it in again after five 

seconds.

•  Reset the power supply. Unplug the supply and plug it in again after five 

seconds.

Phone with tone service dials out in pulse mode

•  Make sure phone is in tone dialing mode.

Phone won’t dial out with pulse service

•  Make sure phone is in pulse dialing mode.

Handset displays 

•  Place the handset on the main base for reset.
•  An additional handset is in use.
•  Move closer to the base.

Can’t hear messages, beep, etc.
•  Adjust speaker volume.
Time/Day setting is incorrect.
•  Set the time clock. 
Answers on 10th ring
•  Make sure answering system is turned on.
•  Answering system memory may be full. Erase some messages.
Incoming messages are incomplete
•  An extension phone may have been lifted as a message is received.
•  Answering system memory is full. Erase some messages.
•  You may have accidently pressed the PLAY/STOP button during playback 

and stopped the message.

Won’t respond to remote commands
•  You must use a tone-dial phone. This phone does not support pulse 

(rotary) dialing.

•  Make sure to enter the correct security code.
•  Did unit hang up? If you take no action for a period of time, it automatically 

hangs up.

•  Aluminum siding.
•  Foil backing on insulation.
•  Heating ducts and other metal construction can shield radio signals.
•  You’re too close to appliances such as microwaves, stoves, computers, 

etc.

•  Atmospheric conditions, such as strong storms.
•  Base is installed in the basement or lower floor of the house.
•  Base is plugged into an AC outlet with other electronic devices.
•  Baby monitor is using the same frequency.
•  Handset battery is low.
•  You’re out of range of the base.

To keep your telephone working and looking good, follow these guidelines:

•  Avoid putting the phone near heating appliances and devices that 

generate electrical noise (for example, motors or fluorescent lamps).

•  DO NOT expose to direct sunlight or moisture.
•  Avoid dropping and other rough treatment to the phone.
•  Clean with a soft cloth. 
•  Never use a strong cleaning agent or abrasive powder because this 

will damage the finish.

•  Retain the original packaging in case you need to ship the phone at a 

later date.

If trouble is experienced with this equipment, for warranty information, please 

contact customer service at  

1-800-448-0329.  If the equipment is causing harm to 

the telephone network, the telephone company may require that you disconnect the 

equipment until the problem is resolved.
Any unauthorized repairs, changes or modifications not expressly approved by 

Thomson Inc. could void the user’s authority to operate this product.  For instructions 

on how to obtain a replacement unit, refer to the warranty included in this guide or 

call customer service at 

1-800-448-0329.

Or refer inquiries to:

Attach your sales receipt to this booklet for future reference or jot down the date this 

product was purchased or received as a gift. This information will be valuable if service 

should be required during the warranty period.
Purchase Date  __________________________________________________  
Name of Store

The following messages show the status of the answering system or 

help you set up and use the system.

0-59 

Indicates the total number of messages.

CL (blinking) 

The voice time/day stamp needs to be set.

- - 

Answering system is turned off.

An (blinking) 

The system is answering a call and  

 

 

recording an incoming call.

F (blinking) 

Answering system memory is full.

The system is recording a memo or an    

announcement.

LA (Line Access) 

Answering system is being accessed  

 

remotely from another location.

A long warbling tone (with ringer on) 

Signals an incoming call 

Three short beeps (several times) 

Page signal

One long tone 

Confirmation tone

One beep every 7 seconds 

Low battery warning

No display

•   Fully charge (for 16 hours) or replace the battery.
•   If you are using AC (electrical) power, make sure that the unit is 

connected to a non-switched electrical outlet. Unplug the AC power 

converter from the unit and plug it back in.

You can access your answering system from any touch-tone phone 

by entering your 3-digit security code after you hear the outgoing 

announcement.
1.  Dial the telephone number to which the answering system is connected 

to.

2.  Enter the security code after you hear the tone.
3.  Follow the voice menu to use the answering system’s remote functions.
The remote feature lets you perform the following functions:

Review message 

1

Play back messages 

2

Stop message playback 

2

Erase message  

0 (during message playback)

Skip message 

3

Turn off/on answerer 

4

Review voice menu options 

7

The default security code for accessing the answering system from another 

location is 

1 2 3. You must use the handset to change the security code. With the 

phone 

OFF (not in TALK mode), follow these steps:

1.  Press the flash/answerer/call waiting button to display 

2.  Press the *EXIT/tone button.
3.  Enter the new 3-digit security code.
4.  Press the *EXIT/tone button again. The unit announces the new code, 

pauses, beeps, and then announces the menu options again.

For hands free operation:
1.  Remove the rubber cap covering the headset jack.
2.  Connect the headset to the headset jack on the handset. The handset 

receiver is disabled when the headset is connected.

3.  Adjust the headset to rest comfortably on top of your head and over your 

ear. Move the microphone to approximately two to three inches from your 

mouth.

4.  Press the TALK/CALL BACK button on the handset to answer a call or make 

calls with the headset.

5.  To return to normal operation, unplug the headset from the jack.

To attach the belt clip, insert the sides of the belt clip into the slots on each 

side of the handset. Snap the ends of the belt clip into place.

1.  Make sure the telephone is 

OFF (not in TALK mode) before you replace 

battery.

2.  Remove the battery compartment door.
3.  Disconnect the cord attached to the battery pack and remove the battery 

pack from the handset.

4.  Insert the new battery pack and connect the cord to the jack inside the 

battery compartment.

5.  Replace battery compartment door.
6.  Place handset in the base to charge. 

A shipping and handling fee will be charged upon ordering. We are required 

by law to collect appropriate sales tax for each individual state, country, 

and locality to which the merchandise is being sent. Items are subject to 
availability.

 

•   To see Caller ID information in your display, you must be subscribed to 

Caller ID service through your local telephone company.

Caller ID incomplete  

•  The unit displays this message if it detects anything other than valid 

Caller ID information during the silent period after the first ring. This 

message indicates the presence of noise on the line. 

Handset can not link.

•  If any handsets become inoperable, place it on the main base cradle for 

20 seconds to re-register.

No dial tone

•  Check or repeat installation steps
•  Make sure the base power cord is connected to a working electrical 

outlet.

•  Make sure the telephone line cord is connected to the base unit and the 

modular phone jack?

•  Disconnect the base from the wall phone jack and connect another 

phone to the same jack. If there is no dial tone on the second phone, 

the problem might be your wiring or local service.

•  The handset might be out of range of the base. Move closer to the base.
•  Make sure the battery is properly charged (for 16 hours).
•  Ensure the battery pack is installed correctly.
•  Did the handset beep when you pressed the TALK/CALL BACK button? 

Did the in use indicator come on? The battery may need to be charged.

Handset does not ring

•  Make sure the ringer is set to ON, this can be done through the handset 

setup menu Ringer Volume.

•  You may have too many extension phones on your line. Try unplugging 

some phones.

•  See solutions for “No dial tone.”

You experience static, noise, or fading in and out

•  Change channels
•  The handset may be out of range. Move closer to the base.
•  Relocate the base.
•  Charge the battery.
•  Make sure base is not plugged into an electrical outlet with another  

household appliance.

Unit beeps

•  Place handset in base cradle for 20 seconds to reset the security code. 

If that doesn’t work, charge the battery for 16 hours.

•  See solutions for “No dial tone.”
•  Replace the battery.

This phone is EXPANDABLE up to a total of 4 handsets (by additional 

purchase of the optional Model 25902 handset with charge cradle).

UNAVAILABLE shows on the display.

Make sure your package includes the items shown here.

• Defects in materials or workmanship.

• One year, from date of purchase. 

(The warranty period for rental units begins with the first rental or 45 days from 

date of shipment to the rental firm, whichever comes first.)

• Provide you with a new or, at our option, a refurbished unit. The exchange unit is 

under warranty for the remainder of the original product’s warranty period.

• Properly pack your unit. Include any cables, etc., which were originally provided 

with the product. We recommend using the original carton and packing 

materials.

• ”Proof of purchase in the form of a bill of sale or receipted invoice which is 

evidence that the product is within the warranty period, must be presented to 

obtain warranty service.” For rental firms, proof of first rental is also required.  Also 

print your name and address and a description of the defect. Send via standard 

UPS or its equivalent to:

• Insure your shipment for loss or damage. Thomson Inc. accepts no liability in case 

of damage or loss.

• A new or refurbished unit will be shipped to you freight prepaid.

What your warranty does not cover:

• Customer instruction. (Your Owner’s Manual provides information regarding 

operating instructions and user controls. Any additional information, should be 

obtained from your dealer.)

• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.

• Please complete and mail the Product Registration Card packed with your unit. 

It will make it easier to contact you should it ever be necessary. The return of the 

card is not required for warranty coverage.

• Some states do not allow the exclusion nor limitation of incidental or 

consequential damages, or limitations on how long an implied warranty lasts so 

the above limitations or exclusions may not apply to you.

• This warranty gives you specific legal rights, and you also may have other rights 

that vary from state to state.

If you purchased your product outside the USA:
  • This warranty does not apply. Contact your dealer for warranty information.

 

1. Locate battery and battery door which are packaged together inside a 

plastic bag and are separate from the handset.

2.  Locate the battery compartment on the back of the handset.
3.  Plug the battery pack cord into the jack inside  the compartment.

4.  Insert the battery pack.
5.  Close the battery compartment by pushing the door up until it snaps into 

place.

6.  Place the handset in the base  to charge.

1.  Plug the AC power converter of the extra charging cradle into the 

electrical outlet.

2.  Place the handset in the extra charging cradle. The charge indicator turns 

on, verifying the battery is charging. 

3.  Allow the phone to charge for 16 hours.

YOU MUST REGISTER THE HANDSET TO THE MAIN BASE BEFORE USE!
After the optional handset has charged for 16 hours on the extra charger, place 

it on the main base station for 20 seconds, it will then automatically register.

NOTE: PLEASE REGISTER  shows on the display if the 

completed registration successfully, READY will show on 

UNAVAILABLE when the TALK/CALL BACK button is pressed.